manualshive.com logo in svg

Clean Water Systems 7500-S1, Installation Manual

Share
Download
Clean Water Systems 7500-S1 Installation Manual Download Page 12

7500-S Sediment Filter Installation & Startup Guide 

Page 4

 

www.cleanwaterstore.com 

Rev 083016 

 

 

Program the 7500 S Valve 

 

Turn On Valve: 

 

Plug the valve in, and wait for the Service Screen to come on, the Dynamic Display Strip is 

blinking and the numbers 3101 will flash briefly, indicating you have a filter valve and not a 

softener type valve. 

 

Unlock  

 

When first powered up the valve will not be locked, but after several minutes will lock.  During 

the programming if you need to unlock, and the blue Key Icon on right is lit, press and hold both 

Scroll Buttons to unlock.  The valve will beep, and the blue key Icon will disappear. 

 

Set Time 

 

Press the Menu/Confirm button (far left) once and the blue wrench icon and time clock icon will 

display. 

 

Press the Menu/Confirm button again to set the time.  The hours digit will flash.  Adjust the 

hours with the scroll arrows.  Clock time is 24‐ Hour (or Military Time), so 1 pm is 13:00, two pm 

is 14:00, etc.…   

 

Press the Menu/ Confirm button when done.  The time you set will now be displayed, and not 

flashing.   

 

Press the Scroll Down button to continue, A‐00 will display. 

 

Valve Type 

 

A‐00 is correct setting for time clock (non‐flow meter) valve, do not change.  Press the Scroll 

Down button to continue. 

 

Set Regeneration Time of Day or Night 

 

Set this to 2:00, which means 2:00 AM, in order for filter system to regenerate (backwash and 

rinse) at 2:00 or other time when no water is being used.  Note that during the 10 – 20 

regeneration no water will be able to be used in house, the valve stops water flow to house. 

 

Press the Scroll Down button to continue.  Display will read 1 – 01 

 

 

 

Summary of Contents for 7500-S1

















Reviews:

No comments

Brands by name

Popular brands

Load more brands