Clayton Hornet 500-400 Safety, Operation & Maintenance Download Page 1

January 2019

 

 

 

 

 WARNING

 SAFETY LEGEND

WARNING

 

• A HEPA Filter must be installed in this vacuum at all times

• If this vacuum is used to collect hazardous material, appropriate personal protective equipment may be required

• If this vacuum is intended for dust ignition proof operation, it must be used with supplied or recommended accessories from  

Clayton Associates

• Any alteration to this equipment by a third party will nullify its warranty

 

Hearing protection is recommended when 

operating this equipment.

Respiratory protection is recommended when 

operating this equipment.

Read and understand operator’s manual before 

using this equipment.

Eye protection is required when operating  

this equipment.

WARNING

WARNING

WARNING

WARNING

 

 

 

 

 

Scan this QR code for 

online instructions and 

documentation, or visit

www.ClaytonHowTo.com

Safety – Operation – Maintenance

Keep this document in a safe place

Read and understand this manual before operating your vacuum

Hornet Exp Air  

Dust Ignition Proof Pneumatic Vacuum 

Models with Prefix: 500-400, ACE-300, ACE-400, ACE-500, ACE-1000
• Designed for use in Explosive Dust Atmospheres

• Designed for use in Class II Divison 2 Groups E, F & G Locations

• Designed for use in ATEX Category 3D Zone 22

• Dry Recovery Only

  II 3 D T85ºC

Summary of Contents for Hornet 500-400





















Reviews: