41001019 Iss 02
Consort Equipment Products Ltd
Registered Office: Thornton Industrial Estate
Milford Haven, Pembrokeshire, SA73 2RT
Telephone: 01646 692172 Fax: 01646 695195
I
NSTALLATION
,
O
PERATION AND
M
AINTENANCE
I
NSTRUCTIONS FOR
R
ECESSED
W
ARM
A
IR
C
EILING
H
EATER
F
OR
W
IRELESS
E
LECTRONIC
C
ONTROLS
Model Number: HE7230W
RETAIN THIS LEAFLET FOR FUTURE MAINTENANCE
The Claudgen recessed ceiling heater is designed to fit in place of a
standard 600mm ceiling panel. It is supplied complete with a
remote mounting control
box.
IT IS ESSENTIAL THAT THE CEILING FRAME IS ADEQUATELY
SUPPORTED TO SUPPORT THE WEIGHT OF THE HEATER, OR THAT
THE HEATER IS INDIVIDUALLY SUPPORTED. THERE IS PROVISION
ON THE HEATER FOR CHAIN OR WIRE, SUPPORT OR MOUNTING.
IT IS ALSO ESSENTIAL THAT THE HEATER IS NOT INSTALLED IN A
CONFINED SPACE, NEAR VERTICAL WALLS OR NEAR THE CORNER
OF A ROOM.
NB: Weight of HE7230W: 12.4 Kg
I
NSTALLATION
Carefully unpack the unit and control box. The unit is supplied with
a length of self-adhesive foam strip. This can be cut into lengths
and is to be laid on the 4 sides of the ceiling frame (see Fig 3). This
will ensure that the unit assembly is free from vibration. The
discharge grille and diffuser assembly can now be fitted into the
ceiling frame (see fig 3).
C
ONNECTION TO THE
M
AIN
S
UPPLY
This unit is suitable for connection to 230/240V 50Hz supplies.
The HE7230W has a heating load of 3 kW.
The unit must be wired in accordance with IEE regulations for the
Electrical Equipment of Buildings and the installer should ensure
that a suitable isolating switch is connected in the mains supply.
Fig. 2 shows wiring diagram.
The electrical connections are accessible so that the unit can be
wired in site (see Fig 1).
O
PERATION
This heater can only be used when connected to a CZC1 wireless
programmable timer
. Each CZC1 can control any number of
heaters. The heater has an indicator light positioned behind the
fascia panel on the top right side. The light may be:
Green
-
when no heat is needed
Yellow
-
when some heat is needed to maintain the
room temperature
Red
-
when the heater is on full power
Fast Flashing Red -
when the heater has overheated and the
Electronic Safety Control has switched the
heater off.
Please refer to the CZC1 user and operating instructions for full
operational details.
M
OUNTING
The fan heater box can only be fitted one way round (see Fig.1), as
2 of the studs are offset. This ensures that the fan outlet lines up
with the discharge grille and also that the wiring is always sighted
the same side.
The diffuser is attached to the discharge grille with 4 small clips
which can be removed if necessary.
The discharge grille has 4 additional studs, plus nuts/washer, to
enable the unit to be chain mounted, if required.
There are also extra holes in the box to enable the unit to be
suspended via wires.
MAINTENANCE
ALWAYS ENSURE THAT THE MAIN EXTERNAL ELECTRICITY SUPPLY IS
SWITCHED OFF BEFORE SERVICING THIS HEATER.
To obtain the best results from the heater, it is essential to avoid
the accumulation of dust and dirt within the unit on the air inlet
and discharge grilles. Regular cleaning is necessary with particular
attention to the removal of any dirt on the fan rotor blades.
Cleaning of the fan is best carried out with a soft brush.
E
LECTRONIC
S
AFETY
C
ONTROL
The appliance is fitted with an Electronic Safety Control (ES).
This is a safety device which switches the heater off if, for any
reason, the appliance overheats. The overheating is indicated by a
fast flashing red light. The ES control can only be re-set after the
appliance has cooled down. In order to re-set the ES control,
proceed as follows:
•
Switch the appliance off at the mains by using isolator switch
and leave to cool down for approximately 5 minutes.
•
Switch appliance back on and the ES control will re-set.
•
Ensure that the appliance is functioning correctly. If the ES
control operates again, the appliance should be checked by a
competent electrician.
TO REPLACE A FAN/HEATER ASSEMBLY
a)
Switch off the mains supply
b)
Release the six nuts and washers fixing the fan heater box to the
discharge grille
c)
Disconnect the wiring
d)
Remove the fan heater from the box (four screws)
e)
Fit the replacement unit and re-assemble in the reverse order.
