Clatronic DBS 3187 R, Instruction Manual

Page: 33 / 54

E
N
G
LI
S
H
ENGLISH
33
Steam Ironing
WARNING:
The steam brush and the iron eject a large quantity of hot
steam. Danger of burns.
CAUTION:
When using the steam iron please ensure that the water tank
is always fi lled to the required level. Operating the device
without water will damage it.
• Fill the tank up to the maximum mark. Do not overfi ll!
• Close the water tank and put it back on the base.
• Connect the base station to a 230 V / 50 Hz socket with
earthing contact.
• Turn on the switches (11) and (12).
• Set the desired temperature.
• When the control lamp (9) on the base lights up you can
start ironing.
• Press the steam jet button if necessary.
NOTE:
Keep a cloth ready! At fi rst water may also be expelled from
the soleplate of the iron.
How can I replenish the water during operation?
Refi ll with water before the tank is completely empty. The lamp
(10) shows that there is not enough water.
• Place the iron on the heel rest.
• Turn off the steam with the switch (11).
• You can remove the tank and then fi ll it up.
• Replace the tank on the base. You can now continue
operation.
Operating the steam Brush
WARNING: DANGER OF BURNS!
• Particularly when using the steam brush it is advisable to
protect yourself, e.g. by means of protective goggles, long-
armed clothing, gloves etc.
• Please also note our other warnings and instructions for
use.
NOTE:
The steam brush has a catch with which you can remove the
brush attachment.
You can use the steam brush to refresh or remove creases from
the clothes, or brush them off under steam.
For this purpose it is best to put your clothes on a hanger.
• While you are using the brush, guide it gently over the
laundry.
• If you are using only the jet of steam the distance should be
approximately 2-3 cm.
When you have fi nished
• After use, always turn the temperature control to „ MIN “ (the
control lamp in the handle of the iron goes off).
• Turn the switches (11) and (12) off.
• Remove the mains plug from the socket.
• Empty the water tank.
• Allow the device to cool down before you put it away.
Cleaning
• Always remove the mains lead before cleaning!
• Wait until the machine has cooled down completely.
• Clean the casing with a slightly damp cloth.
• Clean the sole plate and the rest with a slightly damp cloth.
Do not use any abrasive cleaning agents!
• The device must never be immersed in water!
Troubleshooting
Fault Possible Cause Remedy
Device does not
work Faulty mains socket Try another socket
Loud noises
during steam
operation The tank is empty Check the tank
During steam
operation water
is also expelled • The temperature
control on the iron
is set too low
• It is possible that at
fi rst water will also
be expelled
• Select a higher
temperature
• Press the steam jet
button for approx.
1 minute until no
further water comes
out
The device
suddenly stops
working during
operation Is the electric circuit
overloaded? Check the house fuse
Technical Data
Model: .........................................................................DBS 3187 R
Power supply: ............................................................230 V, 50 Hz
Power consumption: .......................................................... 2100 W
Protection class: ...........................................................................
Ι
Maximum fi lling quantity of the water tank: ...................... 1,2 litres
Net weight: ...........................................................................3,7 kg
This device has been tested according to all relevant current
CE guidelines, such as electromagnetic compatibility and low
voltage directives, and has been constructed in accordance with
the latest safety regulations.
Subject to technical changes without prior notice!
05-DBS 3187 R.indd 33 05-DBS 3187 R.indd 33 21.09.2007 10:48:33 Uhr 21.09.2007 10:48:33 Uhr