E
N
G
LI
S
H
ENGLISH
33
Cable winding device
Pull out the cable up to the maximum length indicated with the
yellow mark. Never pull the cable out up to the red mark as the
cable winding can be damaged. Said damages are not covered
by the warranty.
Winding
Press the cable winding button and guide the cable. Hold the
cable to avoid wrapping.
Telescope Vacuum Pipe
The height-adjustable vacuum pipe
enables individual alignment to your
height.
Unlock the coupling by pressing the key
in the direction of the arrow.
Slide the vacuum pipe to the desired
length. To lock the device, release the
key until you hear it lock in place.
Nozzle accessories
Groove and brush
nozzle:
For vacuuming upholstery, curtains and
in corners and crevices etc.
Upholstery nozzle:
For cleaning upholstery, curtains etc.
Floor nozzle:
To clean carpets or smooth surfaces.
Smooth fl oors:
Press down the lever with the brush
symbol „
“ with your foot.
The brush is now visible..
Carpets:
Move the lever with your foot to the
„
“symbol.
Parquet brush:
The fl oor nozzle is fi tted with rollers for
improved manoeuvrability. For large
areas such as parquet, laminate or
tiles etc.
Turbo brush:
The fl oor nozzle is fi tted with rollers for
improved manoeuvrability. The brush is
equipped with a rotating and swivelling
brush roller driven by the air current.
Removes ground-in dirt, animal hairs,
threads and fl uff particularly thoroughly.
The carpet pile is brushed up to look
almost new.
Move the switch on the brush to Sym-
bol A in order to increase the quantity
of suction air. In the case of symbol
(B) this is correspondingly less. This
increases the suction power.
Please note that the turbo brush is
not suitable for smooth fl oors, e.g.
parquet, laminate etc. as the surface
might be damaged.
Releasing the nozzles: Pull these off while turning slightly.
Air Slide
Open the air slide on the hose handle in order to regulate the
airfl ow or to clear any particles sticking to the nozzle.
Filter
Your machine has three fi lter systems. The traditional dust bag
system has been replaced by a transparent dust container. In
this, coarse dirt particles and tiny particles fl oating in the air are
swirled out of the suction air by the high speed of the air current.
It is therefore unnecessary to buy dust bags.
Once the dust level has reached the MAX mark on the dust con-
tainer, or the suction power of the vacuum cleaner is reduced,
please proceed as follows:
Ill. 1
Emptying the Dust Container
• Press the button to release the
dust container and remove it
from the vacuum cleaner.
Ill. 2
• Pull
the
fi lter insert out
care-
fully
by the two retainers. Move
the dust container to a vertical
position if necessary.
• Empty the contents of the dust
container. Then put the fi lter
insert back in position. Please
ensure that the fi lter insert is
reinstalled fi rmly in an upright
position.
Attach the dust container again
by locking it in position.
Ill. 3
1. Motor Protective Filter
(in the Dust Container)
Cleaning the Filter Element
• Press the button to release
the dust container and then
remove it (see illustration 1).
• Empty the contents of the
dust container (see Illustration
2). Unlock the fi lter insert by
turning it a short distance in
a clockwise direction (see
Illustration 3). In the second
step the fi lter insert can be
pulled out towards the bottom.
Clean the motor protection fi lter
by tapping and gently brushing
out.
• Now replace the components.
• Attach the dust container again
by locking it in position.
05-BS 1273.indd 33
05-BS 1273.indd 33
07.03.2008 8:24:45 Uhr
07.03.2008 8:24:45 Uhr