background image

Step 4: Install the frame supports

The bottom of the long leg of the frame 

support (the end without endcaps) [2] bolts to 
the tab on the end of the lower mounting bar 
[1]. 

The bolt hole you use on the frame support 

depends on the mounting height of the lower 
horizontal mounting bar.

If the horizontal mounting bar is:

17"- 19" from the ground use the bottom hole
19"- 21" from the ground use the middle hole
21"- 24" from the ground use the top hole

Bolt them together with a 1/4"-20 x 1-1/4" 

bolt [B] and a 1/4"-20 locknut [F]. 

Snug down the nut and repeat the 

installation on the other side.

Step 5: Assemble the frame 

supports

Slide the two-piece frame supports [2] 

together. Match up the holes and slide in the 
frame pin [L] and fasten to lock in position.

Step 6: Install the upper horizontal 

mounting bar 

Swivel the frame supports [2] up until the 

short leg is parallel to the ground. 

The holes in the frame supports give an 

approximate position (any hole may be used) 
for mounting the upper horizontal mounting 
bar onto the handlebar.

You want to place the upper horizontal 

mounting bar as far as possible from the 
lower mounting bar and insure clearance from 
controls, lights and moving parts. You can 
mount this bar on the front or back of the 
handlebars. 

After determining the correct position, bolt the 
bar to the handlebars in the same way as the 
lower horizontal mounting bar (see step 3).

Step 7: Attach the frame supports

Align the chosen frame support hole with 

the hole in the end of the upper horizontal 
mounting bar. Bolt them together with a 1/4"-
20 x 1-1/4" bolt [B] and a 1/4"-20 locknut [F]. 

Lightly tighten the nut. Repeat on the other side.

Step 8: Check and adjust the 

frame supports

The upper leg of the frame supports (the 

end with the endcaps) [2] should be parallel 
to the ground and the ends should be about 
28.5" (outside to outside) away from each 
other. If parts are in this position proceed 
to step 9. If not see below for adjustment 
procedures.

If short leg of the frame supports are not 

parallel to the ground.

10

1

2

2

2

F

B

2

2

L

2

2

L

Frame support 

assembled with 

frame pin

Summary of Contents for Deluxe Snow Thrower Cab















Reviews: