CLAS OP 0500 Manual Download Page 6

clas-equipements.com

clas-equipements.com

PNEUMATIC EQUIPMENT

TOOLING APPLICATION

AIR SUPPLY REQUIREMENTS

• Supply the tool with 6.3bar of clean, lubricated, dry air. Higher pressure drastically reduces tool life and/or can 

cause sever injury.

• Connect the tool to the airline using pipe, hose and fitting sizes.

• Do not install a quick coupler directly into the air hose connector.

• In order to have the tool working to full satisfaction, the minimum air supply must beat least 10% higher than the 

indicated air consumption of the air tool.

• Use recommended hose size and length. Don not connect the tool to the airline system without incorporating an 

easy to reach and operate air shut off valve.

• Air supply should be lubricated.

Impact wrench

For tightening and unscrewing of threaded fastener

Ratchet

Tightening and unscrewing of various kinds of bolts and nuts

Drill

For drilling holes in metals, wood and plastics

Screwdriver

For tightening and unscrewind of wood ant metal screws with hex and Phillips 

head

Sanders

To remove layers of paint and filling material

Polisher

To polish painted surfaces and finish surfaces prior to painting

Air saw

For cutting sheet steel, carbody panels, pipes, steel, plastic and wood

File

File for metals, wood and plastics

Air hammer

To cut car body panels, bolts, screws and nuts

Needle scaler

To remove rust, paint and cinder after welding

Windscreen cutter

To remove cement, sealing material and rubber from windscreen frame

Nibbler

To cut (nibble) car body panels, sheet steel, stainless steel and corrugated 

panel sheets

Shear

With this tool you can cut metal plate

Die grinder stell

For use with bonded abrassive mounted grinding wheels rotary files and car-

bide burrs providing their speed rating matches the speed of the grinder

Angle grinder

Light grinding and dressing of welds

Blind riveting

To rivet two metal panels together

Belt sander 

For sanding and polishing in confined areas

Engraving pen

To mark tools and parts made out of metal, stone and other hard materials

Cut off tools

Used for cutting operation on bearings, exhaust pipes and clamps

Spot weld drill

For controlled removal of spot welds on car body repairs

Sticker grinder

For removing sticker, labels and tags from painted flat surfaces

Summary of Contents for OP 0500













Reviews: