background image

UNITED KINGDOM

 www.clasohlson.co.uk

Ver

. 20211025

LED Ceiling Light

Art.no  36-7306-1 Model  K-NCF-LN10W

 

36-7306-2  

K-NCF-LN20W

Please read the entire instruction manual before use and 
then save it for future reference. We reserve the right for any 
errors in text or images and any necessary changes made 
to technical data. In the event of technical problems or other 
queries, please contact our Customer Services.

Safety

The light source of this luminaire is not replaceable: when the 
light source reaches its end of life the whole luminaire shall be 
replaced.

2.  Open the end piece.
3.  Remove the end 

piece and take off 
the plastic cover.

Responsible disposal

The light fitting is Class 1 rated and must therefore be 
earthed.

The light source is not suitable for use with a dimmer.

 

Warning:

•  This light fitting is only suitable for permanent installation 

and should be installed by a qualified electrician.

•  The light fitting should be mounted out of the reach.
•  Ensure proper footing and balance at all times during 

installation.

• 

 Whenever installing any electrical products, basic 

safety precautions should always be observed to avoid 
the risk of fire, electric shock and personal injury.

Installation

 

Warning:

1.  Before beginning any electrical installation 

always disconnect the power to the circuit 
you are working on, either by turning off 
the main circuit breaker or by removing 
the fuse from the consumer unit.

4.  Using the light fitting as a template mark out where you 

may need to drill/screw. 

 

Warning: 

Make sure that the wall has no concealed 

electrical wiring, gas or water pipes before drilling/
screwing. Use an appropriate fastening method for 
the surface in question.

5.  Make a hole in one of the silicone plugs in the end piece. 

Pull the supply cable through and connect it to 
the terminal block.

6.  Turn the power on.

 Use the same installation procedures described above to 

connect several light fittings in series (36-7306-1 Max 10, and 
36-7306-2 Max 5).

This symbol indicates that this product 
should not be disposed of with general 
household waste. This applies throughout 
the entire EU. In order to prevent any harm to 
the environment or health hazards caused by 
incorrect waste disposal, the product must 
be handed in for recycling so that the material 
can be disposed of in a responsible manner. 
When recycling the product, take it to your 
local collection facility or contact the place of 
purchase. They will ensure that the product is 
disposed of in an environmentally sound manner.

Specifications

36-7306-1

Rated voltage 

220–240 V AC, 50/60 Hz

Light source 

LED 13 W

Colour temperature 

3000 K

Colour rendition (Ra) 

> 80

Luminous flux 

1415 lm

Beam angle 

110°

IP rating 

IP21

Size 

600 × 165 × 66 mm

36-7306-2

Rated voltage 

220–240 V AC, 50/60 Hz

Light source 

LED 24 W

Colour temperature 

3000 K

Colour rendition (Ra) 

> 80

Luminous flux 

2890 lm

Beam angle 

110°

IP rating 

IP21

Size 

1200 × 165 × 66 mm

Summary of Contents for CO/Tech K-NCF-LN10W

Page 1: ...ain circuit breaker or by removing the fuse from the consumer unit 4 Using the light fitting as a template mark out where you may need to drill screw Warning Make sure that the wall has no concealed electrical wiring gas or water pipes before drilling screwing Use an appropriate fastening method for the surface in question 5 Make a hole in one of the silicone plugs in the end piece Pull the supply...

Page 2: ...genom att ta bort slå av säkringen i elcentralen 4 Använd armaturen som mall och märk ut var du ev behöver borra skruva Varning Försäkra dig om att taket är fritt från el och vattenledningar där du avser att skruva borra Använd för taket lämplig fästmetod 5 Gör hål i gavelns silikonpluggar dra igenom inkommande ledning och anslut den till kopplingsplinten 6 Slå på strömmen Du kan koppla samman fle...

Page 3: ...le til enten med hovedstrømbryteren eller ved å fjerne sikringen i sikringsskapet 4 Bruk armaturen som mal og merk hvor du skal bore skru Advarsel Før boring i veggen må du forsikre deg om at det ikke er skjulte strømledninger eller vannrør i takkonstruksjonen Bruk en festemetode som er beregnet på materialene i taket 5 Lag hull i gavlens silikonplugger trekk innkommende ledning gjennom og koble d...

Page 4: ...n johdon virta ennen asentamista sammuttamalla se joko päävirtakytkimestä tai irrottamalla sulake sähkökaapista 3 Merkitse mahdolliset asennusreiät käyttäen seinätelinettä mallina Varoitus Varmista että katossa ei ole poraus ruuvauskohdassa sähkö ja vesijohtoja Käytä kattoon sopivaa kiinnitystapaa 4 Tee reiät päätyjen silikonitulppiin vedä sisään tuleva johto läpi ja liitä se liiitinrimaan 5 Kytke...

Reviews: