background image

Clarke

®

  American Sanders  U. S. Warranty

This Clarke American Sanders Industrial/Commercial Product is warranted to be free from defects in

materials and workmanship under normal use and service for a period of one year from the date of purchase,
when operated and maintained in accordance with Clarke American Sanders's Maintenance and Operations
instructions.

This warranty is extended only to the original purchaser for use of the product.  It does not cover normal

wear parts such as electrical cable, rubber parts, hoses and motor brushes.

If difficulty develops with the product, you should:

(a). Contact the nearest authorized Clarke American Sanders repair location or contact the Clarke American
Sanders Service Operations Department, 2100 Highway 265, Springdale, Arkansas 72764, for the nearest
authorized Clarke American Sanders repair location.  Only these locations are authorized to make repairs to
the product under this warranty.
(b). Return the product to the nearest Clarke American Sanders  repair location.  Transportation charges to
and from the repair location must be prepaid by the purchaser.
(c). Clarke American Sanders will repair the product and or replace any defective parts without charge within
a reasonable time after receipt of the product.

Clarke American Sanders's liability under this warranty is limited to repair of the product and/or replace-

ment of parts and is given to purchaser in lieu of all other remedies, including INCIDENTAL AND CONSE-
QUENTIAL DAMAGES.

THERE ARE NO EXPRESS WARRANTIES OTHER THAN THOSE SPECIFIED HEREIN.  THERE ARE NO

WARRANTIES WHICH EXTEND BEYOND THE DESCRIPTION OF THE FACE HEREOF.  NO WARRANTIES,
INCLUDING BUT NOT LIMITED TO WARRANTY OF MECHANTABILITY, SHALL BE IMPLIED.  A warranty
registration card is provided with your Clarke American Sanders product.  Return the card to assist Clarke
American Sanders in providing the performance you expect from your new floor machine.

Clarke

®

,  2100 Highway 265, Springdale, Arkansas 72764

Clarke American Sanders  reserves the right to make

changes or improvements to its machine without notice.

Always use genuine Clarke American Sanders Parts for repair.

               2100 Highway 265

Springdale, Arkansas, 72764

Division of

Summary of Contents for Super E Edger

















Reviews: