background image

5

Parts & Service: 020 8988 7400/E-mail:[email protected] or [email protected]

INSTALLATION

Because of the variety of possible installations, no plumbing accessories are
supplied with your pump, however accessories are available from your
nearest CLARKE dealer. Contact your CLARKE dealer for further information,
or CLARKE International Sales Department on 01992 565333.

Note: It is recommended that the end user should consult a qualified installer

if there are any doubts as to the suitability of this product for a particular
installation.

IMPORTANT: The pump MUST NOT be connected to the mains power supply
until all hose/pipe installation is completed.

INSTALLATION OF THE PUMP

A typical installation of the pump is shown in Fig 1. The pump must always be
installed and operated in a horizontal position i.e. with the outlet port facing
vertically upwards. The fixing holes in the base should be used to secure the
pump firmly in it’s operating position. Mount the pump on raised blocks or a
purpose built platform to protect it from flooding.

Always ensure there is adequate air circulation around the motor and that
the transparent filter cover is accessible so that the filter basket can be
removed for cleaning. The pump should be installed in a dry, well ventilated
enclosure, sheltered from rain, such as a purpose built pump room.

The pump is usually installed between the pool skimmer and the pool filter
and should be positioned as near to the pool water level as possible.

Fig 1

Pool

Skimmer
outlet

Pool Filter

Pool Side

Remote Power
Connection

Summary of Contents for SPP10 7175030

















Reviews: