Clarke PB-12 Operator'S Manual Download Page 9 | Manualshive

Page: 9 / 25

Clarke PB-12 Operator'S Manual Download Page 9

CLARKE TECHNOLOGY PB-12 Operator's Manual

Page 8

How To Prepare The Machine For Operation

(cont)

How to Connect the Hoses

The hoses for the solution and vacuum are provided with
the tank extractor.

Connect the vacuum hose to the hose connector on the
extractor and to the hose connector on the power brush
tool.

The solution hose has quick-disconnect couplings. To
connect the solution hose to the extractor, follow this
procedure:

1. Pull the knurled collar back.

2. Put the coupling over the fitting on the handle assembly.

3. Release the knurled collar.

See figure 13

How To Adjust The Handle

To adjust the handle, follow this procedure:

1. The locking lever is on the lower part of the handle tube.

Lift the lever with your foot.

2. Lower the handle to the best operating position.

NOTE:

For best operation, raise the handle until the

wheels are just above the floor. Keep your back
straight.

3. Using your foot, push the locking lever down. See figure

Figure 13

Figure 14

«
...
7
8
9
10
11
...
»

Summary of Contents for PB-12


























Reviews:

No comments