Clarke IG1000 Operation & Maintenance Instructions Manual Download | Manualshive

Page: 11 / 28

background image

11

CHECKING THE AIR FILTER

1. Remove the left side maintenance panel.

2. Remove the air filter cover screw

shown on the right.

3. Remove the air filter cover

4. Remove the air filter element.

5. Make sure that the air filter is

clean and not damaged.

• If the air filter is damaged

contact Clarke spare parts
department for a replacement
See page 2

• If the filter is dirty, wash the filter

in a solution of warm water and
mild detergent and rinse thoroughly. Leave the filter to dry
completely, once it is dry immerse the filter in clean engine oil and
sqeeze the filter to remove excess oil.

6. Replace the filter back into its original position and replace the air filter

cover.

WARNING: DO NOT USE INFLAMMABLE SOLVENTS OR PETROL TO CLEAN
THE AIR FILTER.

«
...
9
10
11
12
13
...
»

Summary of Contents for IG1000





























Reviews:

No comments

Related manuals for IG1000

Brand: Datavideo Pages: 18

Brand: Cablematic Pages: 2

INDUSTRIAL Series

Brand: ICT Pages: 2

Brand: Tvone Pages: 18

Brand: National Instruments Pages: 4

Brand: SunSynk Pages: 10

Brand: FireBird Pages: 44

Brand: A-TS TECHNOLOGY Pages: 87

Brand: Fischer Panda Pages: 214

Brand: B&B Electronics Pages: 2

Giga-McBasic II

Brand: B&B Pages: 2

L.O.C.PRO LP7-4

Brand: PAC Pages: 2

Brand: Shenzhen Huangjintai Electronic Pages: 9

Brand: Velleman Pages: 11

Brand: Cobalt Digital Inc Pages: 126

Brand: Wentronic Pages: 4

Brand: Transition Networks Pages: 16

Brand: TDK-Lambda Pages: 36

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands