background image

Transition Networks                                   

 

SPOEB10xx-105 User Guide 

33618 Rev. C 

https://www.transition.com/

  

Page 

1

 of 

16

 

SPOEB10xx-105  

User Guide 

  Stand-Alone Media Converter 

  Power Over Ethernet (15.4W) 

  10/100Base-TX to 100Base-FX 

  Auto Negotiation & AutoCross 

  Link Pass Through & PSE enable / disable 

  PSE/LPT enable / disable 

  Far End Fault & Auto Link Restore 

Contents 

Introduction ......................................................................................................................................... 2

 

Product Description .............................................................................................................................. 2

 

Models .......................................................................................................................................................... 2 
Optional Accessories .................................................................................................................................... 2 
Distances ...................................................................................................................................................... 2 

Features ............................................................................................................................................... 3

 

Application Example - Power over Cat5 to Remote Devices .................................................................... 3

 

Packing List ........................................................................................................................................... 3

 

Installation ........................................................................................................................................... 4

 

Set the Configuration DIP Switch ................................................................................................................. 4 
Eight-position Configuration Switch (SW1) .................................................................................................. 4 
Additional Features ...................................................................................................................................... 6 

Far-End Fault (always enabled) ................................................................................................................ 6 
Automatic Link Restoration (always enabled) .......................................................................................... 6 

Installing Fiber Cables ................................................................................................................................... 7 
Installing the Copper Cable .......................................................................................................................... 7 
Connecting Power ........................................................................................................................................ 8 

Operation ............................................................................................................................................. 9

 

Status LEDs ................................................................................................................................................... 9 
PoE Status LED Scheme ................................................................................................................................ 9 

Cable Specifications ............................................................................................................................ 10

 

Copper Cable .............................................................................................................................................. 10 
Fiber Cable .................................................................................................................................................. 10 

Fiber Specifications ................................................................................................................................. 10 

Technical Specifications ...................................................................................................................... 11

 

Troubleshooting ................................................................................................................................. 12

 

Safety Warnings and Cautions .................................................................................................................... 13 

Service, Warranty and Tech Support .................................................................................................... 13

 

Warranty ..................................................................................................................................................... 13 
Contact Us .................................................................................................................................................. 13 

Compliance Certifications .................................................................................................................... 14

 

Declaration of Conformity .......................................................................................................................... 15 
Electrical Safety Warnings .......................................................................................................................... 16 

Record of Revisions ............................................................................................................................. 16

 

 

Summary of Contents for SPOEB1011-105

















Reviews: