Clarke IBC7 Operation & Maintenance Instructions Manual Download Page 3

3

Parts & Service: 020 8988 7400 / E-mail: [email protected] or [email protected]

SAFETY PRECAUTIONS

PLEASE READ BEFORE USING THIS UNIT

1. Battery acid is highly corrosive. If spillage occurs, wipe off immediately and 

wash copiously with water. Particularly avoid contact with the eyes, but if 
this occurs, you must seek medical advice.

2. Before charging ensure the battery terminals are clean and that the cells 

are filled with electrolyte to the correct level by adding distilled water 
where necessary.

3. This product is not intended for use by persons with reduced physical, 

sensory or mental capabilities or lack of experience and knowledge.

4. Children must not play with the charger. 

5. Do not expose this charger to rain.

6. Never touch the negative and positive leads together.

7. Never attempt any repairs yourself. If you have a problem with your 

charger contact your local Clarke dealer or contact 
[email protected]

8. When charging is completed, ensure that the vehicle battery leads are 

secured to the proper terminals which should be clean, and lightly 
smeared with petroleum jelly to prevent corrosion. Finally, re-check the 
electrolyte level.

WARNING: ALWAYS SWITCH OFF THE CHARGER WHEN CONNECTING OR 
DISCONNECTING LEADS TO AVOID SPARKING AS HIGHLY INFLAMMABLE 
HYDROGEN GAS IS RELEASED IN THE PROCESS OF BATTERY CHARGING 

WARNING: CERTAIN TYPES OF SEALED OR MAINTENANCE-FREE BATTERIES 
NEED EXTRA CARE WHEN CHARGING. PLEASE CONSULT THE BATTERY 
MANUFACTURERS INSTRUCTIONS BEFORE USING THIS UNIT.

WARNING: SINCE TOXIC FUMES MAY BE RELEASED DURING BATTERY 
CHARGING, ONLY USE THIS UNIT IN A WELL VENTILATED AREA.

Summary of Contents for IBC7





















Reviews: