Clarke DEVIL 4000 Operation & Maintenance Instructions Manual Download Page 3

3

Parts & Service: 020 8988 7400 / E-mail: [email protected] or [email protected]

GENERAL SAFETY PRECAUTIONS

Read, and make sure you fully 
understand the following precautions 
and the hazards associated with this 
type of equipment.

1. Check the heater thoroughly for 

damage. DO NOT operate a 
damaged heater.

2. DO NOT modify the heater or 

operate a heater which has been 
modified from its original 
condition.

3. Use only propane gas.

4. Use only VAPOUR WITHDRAWAL 

propane supply. If there is any 
question about vapour 
withdrawal, ask your propane 
dealer.

5. Mount the propane cylinders 

vertically (shut-off valve up). 
Secure them from falling or being 
knocked over and protect them 
from damage.

6. Locate propane containers at 

least 7ft. (2.13m), from the heater 
and do not direct the exhaust 
toward containers.

7. IMPORTANT: Use only the hose 

and regulator assembly provided 
with the heater. Inspect the hose 
assembly before each use of the 
heater. If there is excessive 
abrasion or wear, or hose is cut, 
replace with the hose assembly 
listed on the parts list before using 
the heater.

8. Not to be used for the heating of 

habitable areas of domestic 
premises.

9. For indoor use only in well 

ventilated areas.

10. If at any time gas odour is 

detected, IMMEDIATELY STOP 
operation until the source of gas 
has been located and corrected.

11. Install the heater such that it is not 

directly exposed to water spray, 
rain and/or dripping water.

12. Maintain minimum clearance 

from normal combustible material 
(e.g. like paper). 

13. Due to the high surface and 

exhaust temperatures, adults and 
children must observe sufficient 
clearances to avoid burns or 
clothing ignition.

14. Operate only on a stable, level 

surface.

15. Do not use with duct work. Do not 

restrict air inlet or exit.

16. Use only the electrical voltage 

specified. 

17. Do not move, handle or service 

while hot or burning. 

18. Use only in accordance with local 

codes of practice.

19. Do not place torsional stress on 

any hoses.

Summary of Contents for DEVIL 4000

















Reviews: