manualshive.com logo in svg

Clarke CPSB100B, Operation & Maintenance Instructions Manual, Page: 12 / 16

Share
Download
Clarke CPSB100B Operation & Maintenance Instructions Manual Download Page 12

12

Parts & Service: 020 8988 7400 / E-mail: [email protected] or [email protected]

2. Unscrew the filter as shown in Fig 

20 and wipe clean.

NOTE: 

Do not use harsh or abrasive 

chemicals when cleaning 
the condensation chamber.

3. Refit the condensation chamber.

REPLACING THE NOZZLE

NOTE: 

ONLY use identical replacement parts when servicing.

After l0-l2 hours of blasting time the nozzle should be checked for wear. The 
nozzle will wear out over time and should be replaced when the hole is no 
longer round or the abrasive media does not flow smoothly through. To 
replace the nozzle:

• Refer to page 14 for the following replacement parts.

1. Disconnect the sandblasting gun from the air hose.

2. Unscrew the nozzle adapter (38), located at the front of the sandblasting 

gun.

3. Remove the old nozzle (37).

4. lnsert the new nozzle.

• A pack of 4 replacement nozzles are available from your Clarke 

dealer: Part number 7640132.

5. Replace the nozzle adapter (38) and firmly screw it onto the gun.

• Keep your sandblaster clean and protect it from damage.

• Check for a worn abrasive material hose and fittings. Watch for 

leaks, blistering, bulging or thinning of the hose.

• Replace any parts which appear worn.

SUITABLE ABRASIVES AVAILABLE FROM YOUR CLARKE STOCKIST

Aluminium Oxide 
Powder

60

60-80

60-80

80

80-120

120

22kg

20kg

7.5kg

22kg

7.5kg

22kg

3052070 3052110 3052100 3052075 3052105 3052080

Glass Bead Abrasive

3052095 20kg

Soda Blast Abrasive

3052805 7.5kg

3052800 22kg

Garnett Abrasive

3052090 22kg

Fig 20

Summary of Contents for CPSB100B

















Reviews:

No comments