Clarke CP range User Instructions Download Page 4

FIRE PREVENTION

ALWAYS

 switch the engine OFF when refuelling.

ALWAYS

 refuel away from any source of heat.

ALWAYS

 refuel in a well ventilated area.

NEVER 

overfill fill the tank, fill to the level specified.

NEVER

 smoke whilst refuelling and avoid smoking or using a naked flame

near the generator.

NEVER

 start the engine if there is a fuel spill. Any spillage must be wiped

clean and the generator allowed to dry before attempting to start the engine.

PREVENTION OF ELECTRIC SHOCK

ALWAYS

 store the generator undercover when not in use and away from

damp or wet conditions.

NEVER

 use the generator when it is raining or snowing or in wet or damp

conditions.

NEVER

 operate the generator with wet hands.

NEVER

 use water or any other liquids to clean the unit.

POSITIONING THE GENERATOR FOR USE

ALWAYS

 leave at least a 1 metre gap between the generator and any

surrounding building or structure.

ALWAYS

 ensure the generator is on a solid, flat surface.

ALWAYS

 ensure the surrounding area is free from any material that could

burn or be damaged by heat.

NEVER

 move or tilt the generator whilst it is switched on.

NEVER

 cover or enclose the generator whilst it is in use.

Be aware of the weight of the generator, do not attempt to lift or move the
generator without the assistance of other personnel or suitable lifting equipment.

EXHAUST GAS PRECAUTIONS

WARNING!: EXHAUST FUMES CAN BE FATAL.

ALWAYS

 ensure that there is adequate ventilation when using the generator.

ALWAYS

 position the generator so that the exhaust is pointing away from

people or animals.

NEVER

 use the generator indoors or in a enclosed area. (i.e. in ware house,

tunnel, well or a hold).

- 3 -

Summary of Contents for CP range









Reviews: