Clarke CIS8612 Assembly Instructions Manual Download Page 11 | Manualshive

Page: 11 / 16

background image

11

Parts & Service: 020 8988 7400 / E-mail: [email protected] or [email protected]

1. Locate the top part of the front door panel (21) near the 3-way peak

connector (6) Disconnect the shoulder cross rail (4) from the 3-way peak
connector (6) and pull the strap onto the connector. Then re-insert the
cross rail to its proper position. as in Fig 13.

CAUTION: DO NOT THREAD THE POLES THROUGH THE SLEEVES. TO
TIGHTEN, WRAP THE OUTER SLEEVES AROUND THE POLES AND TIGHTEN
USING THE STRAPS PROVIDED. (Fig 12)

«
...
9
10
11
12
13
...
»

Summary of Contents for CIS8612

















Reviews:

No comments

Related manuals for CIS8612

CONTEMPORARY PERGOLA

Brand: Grange Pages: 2

Brand: Zempire Pages: 5

Brand: Creative Structures Pages: 17

Brand: Power Fist Pages: 12

Brand: Dometic Pages: 68

Brand: Napier Pages: 7

Brand: Nordisk Pages: 9

Feria Patio Cover 5400

Brand: Palram Pages: 33

Brand: Palram Pages: 54

Brand: Vango Pages: 3

Brand: DARCHE Pages: 8

Brand: Mountain Pages: 44

Juniper 3x2 Extension

Brand: Palram Pages: 40

Brand: Zempire Pages: 2

TaG Clamshell Tent

Brand: PahaQue Wilderness Pages: 2

Brand: Outdoor Play Pages: 2

Brand: COVERPRO Pages: 20

Brand: ABSCO SHEDS Pages: 18

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands