background image

4

Parts & Service: 020 8988 7400 / E-mail: [email protected] or [email protected]

8. NEVER use the wrench if it is defective / operating abnormally.

9. NEVER carry the wrench with your finger on the trigger.

10. NEVER abuse the mains cable of the battery charger. Never yank the 

cable to disconnect it from the socket. Keep the cable away from sharp 
edges/hot surfaces.

11. NEVER use this wrench for any purpose other than described in this booklet.

12. NEVER carry out any alterations or modifications to this product.

13. NEVER wipe the wrench clean with solvents. Wipe plastic parts with a soft 

cloth, slightly dampened with soapy water.

14. NEVER attempt any repairs yourself. If you have a problem with this product 

contact your local CLARKE dealer.

15. ALWAYS use an approved cable extension suitable for the power rating of 

the battery charger (see specifications), the conductor size should also be 
at least the same size or larger than that on the charger. When using a 
cable reel, always unwind the cable completely.

IMPACT WRENCH SAFETY INSTRUCTIONS

1. Use only impact wrench sockets....DO NOT use standard sockets which 

could shatter and cause injury.

2. ALWAYS

 

finish tightening nuts with a torque wrench to the correct torque as 

recommended by the vehicle manufacturer.

3. ALWAYS

 

avoid excessive use of the wrench. When tightening a nut or bolt, 

always avoid over tightening.

4. ALWAYS ensure the wrench has stopped before putting it down after use.

5. ALWAYS only use sockets which are specified for impact wrench use.

6. ALWAYS set the forward/reverse selection bar to neutral when changing 

sockets or when the wrench is not required for immediate use. This will 
avoid accidental starting.

LITHIUM-ION BATTERY USE AND CARE

1. Only use the wrench with the battery pack supplied. Use of any another 

battery pack may create a risk of injury and fire.

2. Do not charge the battery when the room temperature is below 10

o

C. Do 

not store the battery where the temperature may exceed 40

o

C (104

o

F)

3. When the battery pack is not in use, keep it away from metal objects that 

could make a connection from one terminal to another. Shorting the 
battery terminals together may cause burns or a fire.

Summary of Contents for CIR18LiC

















Reviews: