manualshive.com logo in svg

Clarke CDM45C, Operating Instructions Manual, Page: 14 / 16

Share
Download
Clarke CDM45C Operating Instructions Manual Download Page 14

14

Parts & Service: 020 8988 7400 / E-mail: [email protected] or [email protected]

MAINTENANCE

GENERAL CARE

Never use the meter unless the rear cover is secure.

Clean the housing with a damp cloth dipped in a little detergent but never 
chemical solution.

In case of any abnormality, stop using the meter and send it for repair.

REPLACING THE BATTERY

1. Turn off the meter.

2. Unscrew battery cover and remove.

3. Remove the battery and replace with a new one.

4. Clip the battery compartment to the casing and tighten the screw.

REPLACING FUSES

Fuses rarely need replacement. Almost all fuse blows are the result of operator 
error. Fuses should be replaced by the Clarke Service Department with the 
type(s) stated on page 4.

TEST LEAD REPLACEMENT

Replace the leads if they become damaged.

WARNING: BEFORE REMOVING THE REAR COVER, DISCONNECT THE 
PROBES FROM THE CIRCUIT TO BE MEASURED. ENSURE THE COVER IS 
TIGHTLY SECURED BEFORE USING THE INSTRUMENT.

WARNING: REPLACE THE TEST LEADS WITH IDENTICAL OR COMPATIBLE 
LEADS. LEAD SPEC: 1000V 10A.

Summary of Contents for CDM45C

















Reviews:

No comments