manualshive.com logo in svg

Clarke CAT134, Operating & Maintenance Instructions, Page: 14 / 16

Share
Download
Clarke CAT134 Operating & Maintenance Instructions Download Page 14

14

Parts & Service: 020 8988 7400 / E-mail: [email protected] or [email protected]

SPECIFICATION

Please note that the details and specifications contained herein are correct 
at the time of going to print. However Clarke International reserve the right to 
change specifications at any time without prior notice.

Model Number

           CAT134

           CAT135

Part Number

           3120148

         3120149

Max Operating Pressure

                           90 psi (6.2 bar)

Air Consumption

16 cfm (max). Average 5 cfm (CAT134 / 4.5 
cfm -CAT135

Max No Load Speed

                           180 rpm +/-10%

Air Inlet Size

                          1/4“ BSP Female

Sound Pressure Level (LpA dB)

                                  87 dB(A)

Sound Power Level (LwA dB)

                                    98 dB(A)

Uncertainty Factor

                                       K=3

Vibration Levels

     4.35 m/s

2 

(uncertainty factor K= 1.5m/s

2)

Weight 

1.2 kg

1.2 kg

Drive Type

1/2” Square

3/8” Square

Max Torque

                            60 ft/lb +/-10%

Speed Settings (rpm)

                               180 +/-10%

                                140 +/-10%

                                 85 +/-10%

                                 45 +/-10%

Summary of Contents for CAT134

















Reviews:

No comments