manualshive.com logo in svg

Clarke CAS110, Operating & Maintenance Instructions

Share
Download
Clarke CAS110 Operating & Maintenance Instructions Download Page 12

12

Parts & Service: 020 8988 7400/E-mail:[email protected] or [email protected]

CLEANING AND MAINTENANCE

ROUTINE CLEANING

ALWAYS REMEMBER TO DISCONNECT FROM THE MAINS SUPPLY BEFORE
CLEANING THE SPRAY GUN OR PAINT CONTAINER.

Continuous satisfactory operation depends upon proper care and regular
cleaning. It is essential that the spray gun is cleaned thoroughly after every
use. Failure to clean it will almost certainly result in blockages and it may not
operate when you next come to use it! The guarantee does not cover
cleaning a sprayer that has not been properly cleaned by the user. The
following action must be taken after every use:

1. Empty any remaining material from the paint container.

2. Clean the paint container thoroughly with the thinner that was used.

3. Pour some thinner into the paint container and spray through the spray

gun until only clean thinner is coming out of the nozzle.

4. Thoroughly clean the paint pick up pipe and filter with thinner.

5. Clean the spray basket and nozzle and remove paint that remains.

6. Turn the spray gun upside down and apply a few drops of light oil to the

two apertures (A). This will lubricate the piston and cylinder.

INTERNAL CLEANING

If your spray gun should require extra internal cleaning, it may be necessary
to dismantle it. If so, the following action should be taken:

      C

   A

 A

        B

D

E

F

G

Summary of Contents for CAS110





















Reviews:

No comments

Brands by name

Popular brands

Load more brands