background image

4

Parts & Service: 020 8988 7400 / E-mail: [email protected] or [email protected]

ELECTRICAL CONNECTIONS

Before switching the product on, make sure that the voltage of your electricity supply is 
the same as that indicated on the rating plate. This product is designed to operate on 
230VAC 50Hz. Connecting it to any other power source may cause damage.

This product may be fitted with a non-rewireable plug. If it is necessary to change the 
fuse in the plug, the fuse cover must be refitted. If the fuse cover becomes lost or 
damaged, the plug must not be used until a suitable replacement is obtained.

If the plug has to be changed because it is not suitable for your socket, or due to 
damage, it should be cut off and a replacement fitted, following the wiring instructions 
shown below. The old plug must be disposed of safely, as insertion into a mains socket 
could cause an electrical hazard.

If the colours of the wires in the power cable of this product do not correspond with the 
markings on the terminals of your plug, proceed as follows.

• The wire which is coloured 

Blue

 must be connected to the terminal which is 

marked 

N

 or coloured 

Black

.

• The wire which is coloured 

Brown

 must be connected to the terminal which is 

marked 

L

 or coloured 

Red

.

• The wire which is coloured 

Yellow and Green

 must be connected to the 

terminal which is marked 

or 

 or coloured 

Green

.

We strongly recommend that this machine is connected to the mains supply via a Residual 
Current Device (RCD)

If in any doubt, consult a qualified electrician. DO NOT attempt any repairs yourself.

WARNING! Read these electrical safety instructions thoroughly 
before connecting the product to the mains supply.

WARNING! The wires in the power cable of this product are 
coloured in accordance with the following code:
Blue = Neutral      Brown = Live     Yellow and Green = Earth

Plug must be BS1363/A approved.

Always fit a 13 Amp fuse.

Ensure that the outer sheath of the cable is firmly held by the clamp

Neutral

(Blue)

Live

(Brown)

Earth

(Green and Yellow)

Summary of Contents for BR13













Reviews: