background image

- 4 -

]

Fire Prevention

ALWAYS

switch the engine OFF when refuelling.

refuel away from any source of heat.

refuel in a well ventilated area.

NEVER

overfill the tank, fill to the level specified.

smoke whilst refuelling and avoid smoking or using a naked flame near the compressor.

start the engine if there is spilled fuel. Any spillage must be wiped clean and the
compressor allowed to dry before attempting to start the engine.

IMPORTANT  General Notes

NEVER allow anyone, not fully familiar with compressors, to use this equipment.

DO NOT alter the engine settings....these settings are set at the factory. Should they
need recalibration - consult your Clarke dealer

Exhaust Gas Precautions

WARNING:

 Exhaust fumes can be fatal

ALWAYS

 •

ensure there is adequate ventilation when using the compressor.

 •

position the compressor so that the exhaust is pointed away from people or animals

.

WARNING!

DO NOT ATTEMPT TO ALTER ENGINE SPEED SETTINGS

DOING SO WILL INVALIDATE YOUR GUARANTEE

NEVER

 •

use the compressor indoors or in an enclosed area. (i.e. in a warehouse, tunnel, well,
hold etc.)

Summary of Contents for Air SP15ND

















Reviews: