Clarke 8877061 Operation & Maintenance Instructions Manual Download Page 17 | Manualshive

Page: 17 / 28

background image

17

Parts & Service: 020 8988 7400 / E-mail: [email protected] or [email protected]

DC OVER LOAD PROTECTOR

If the DC overload protector
activates, wait for a few minutes and
then press the reset button shown on
the right.

INDICATOR LIGHTS

OUTPUT

The output indicator (Green) will
remain on during normal operation.

OVERLOAD

The overload indicator (Red) will light
up if there is an overload or a short
circuit in the connected appliance.

If this happens, proceed as follows:

1. Turn off any connected electrical

devices and stop the engine.

2. Reduce the total wattage of connected electric devices to within the

rated output of the generator.

3. Check air inlet and around the control unit. If any blockages are found,

remove them.

4. After checking, restart the engine.

OIL ALERT

The oil alert indicator (Red) will light up when the oil level is low.

• To add oil, follow the instructions on page 11

«
...
15
16
17
18
19
...
»

Summary of Contents for 8877061





























Reviews:

No comments

Related manuals for 8877061

Brand: unicraft Pages: 60

Brand: Crystal Vision Pages: 24

Brand: Champion Pages: 30

SKYLINE HFP3000

Brand: INE Pages: 96

Brand: Briggs & Stratton Pages: 8

Brand: ECO POWER Pages: 26

Brand: DR Power Pages: 72

Brand: Curtis Pages: 5

Brand: Curtis Pages: 8

Brand: Bluetti Pages: 17

Brand: Sunstech Pages: 22

Brand: LUCAS Pages: 40

Power Tools RD-GG11

Brand: Raider Pages: 76

Brand: Velleman Pages: 18

Brand: Generac Portable Products Pages: 20

Brand: Generac Portable Products Pages: 42

Brand: Champion Global Power Equipment Pages: 38

Brand: Keysight Pages: 10

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands