background image

4

4. Never climb on, or attempt to ride on the jack.

5. Take care not to trap fingers in the moving parts of the jack.

6.

Ensure that you can see the contact and jacking point throughout the 

jacking operation in case there is any relative movement.

7. This jack is for lifting only, do not move a load using the jack as a dolly.

8. Make sure the load is taken by the full surface of thecylinder or nose, and 

that the point of lift on the load is strong enough to support the load 
adequately.

9. Consult the vehicle handbook to determine the correct lifting points.

10. Do not work under the raised vehicle until it is supported by suitable means 

e.g. axle stands, NEVER rely on the jack to support the vehicle by itself. 

11. Never push a load off the jack.

LIFTING 

O

PERATIONS AND LIFTING EQUIPMENT 

R

EGULATIONS 1998

This jack, depending on use, may fall within the scope of L

O

LE

R

. It is the 

owner’s responsibility to determine whether or not it does, and if so, to comply 
with any applicable requirements. It may be necessary to have the jack 
regularly inspected.

ENVIRONMENTAL PROTECTION

1. Take care to ensure that any spilt hydraulic oil is cleaned away using sand, 

or treated with absorbent granules designed for the purpose.

2. Always make every effort to contain any spillage and prevent ingress into 

the local water course.

Summary of Contents for 7624007













Reviews: