background image

3

Parts & Service: 020 8988 7400 / E-mail: [email protected] or [email protected]

SAFETY PRECAUTIONS

1. Do not exceed the rated capacity of the jack.

2. Do not allow personnel to operate the jack unless they have read these 

safety precautions.

3. Do not operate the jack if damaged.

4. Use the jack in a suitable, well lit work area.

5. Keep the work area clean and tidy and free from unrelated items.

6. Only use the jack on level and solid ground, preferably concrete. Avoid 

soft/unmade ground as the jack may sink in.

7. Ensure non-essential persons keep a safe distance whilst the jack is in use.

8. Ensure there are no personnel or obstructions under the vehicle before 

lowering.

9. Do not work under the vehicle until it is fully supported by axle stands.

10. Keep hands etc clear of the vehicle until lifting is complete.

11.

Ensure that you can see the saddle and jacking point throughout the 

jacking operation in case there is any relative movement.

12. Always ensure that the jack saddle is centred and stable on the lifting point 

before lifting and position the jack to avoid operating it from under the 
vehicle.

13. Check the vehicle weight and recommended lifting points by referring to 

the vehicle owners manual. Ensure the lifting point is not corroded.

14. Never tamper with the jack or modify it in any way, as this could prove to 

be dangerous and will invalidate the guarantee. Only use the jack for the 
purpose for which it is intended.

15. Use appropriate safety equipment, such as protective footwear, when 

using this jack.

16. Ensure that the jack is properly maintained and lubricated at all times, and 

that no corrosion is allowed to weaken any part of it.

17. If the jack has been subjected to an abnormal load or shock, it should be 

removed from service immediately and fully inspected by qualified 
personnel, and passed as serviceable, before being used again.

18. When not in use, store the jack, fully lowered, in a safe, dry, childproof area.

19. Always inspect the jack before use. Ensure that all parts are in good 

condition and operating smoothly, and that no cracks or distortion is 
apparent. If in doubt do not use.

Summary of Contents for 7621037













Reviews: