Clarke 7230330 Operation & Maintenance Instructions Manual Download Page 10

10

Parts & Service: 020 8988 7400 / E-mail: [email protected] or [email protected]

MAINTENANCE

The only maintenance required is a regular inspection to ensure that debris is 
not blocking the passage of water through the pump.

If you suspect the pump is blocked by silt, leaf debris etc, disconnect it from 
the power supply and back-flush to clear any blockage using a hose. You will 
need to disconnect the outlet hose to do this.

Always keep the pump in a clean condition, checking regularly for loose bolts 
or a damaged power cable etc. If the pump has not been used for some time 
it may become stuck but can often be freed up by twisting the screw for that 
purpose, in the end of the main shaft.

The pump should not be taken apart by the user in the case of overhaul being 
required, but should be taken to your nearest Clarke dealer for specialist 
repair.

AFTER USE

After use, and if the pump will not be used over the winter period, or whenever 
there is danger of freezing, always drain the pump body. If the pump has 
been used with contaminated or salty water, it should be thoroughly flushed 
with clean water following use, both inside and out. It should then be drained 
and covered over, if not already installed in a clean, dry environment 
sheltered from the weather.

Remember to re-prime the pump when returning to service.

• In the event that dismantling and overhaul of the pump is necessary, 

contact your Clarke service department.

ENVIRONMENTAL PROTECTION

Through the purchase of this product, the customer is taking on the obligation 
to deal with any waste electrical/electronic equipment in accordance with 
the WEEE Regulations in relation to the treatment, recycling, recovery and 
environmentally sound disposal of the WEEE.

• Any redundant accessories and packaging should be sorted and 

taken to a recycling centre to be disposed of appropriately.

ACCESSORIES

A wide range of accessories is available, including foot valve filters, suction 
and layflat hoses and clips, couplings and 90

°

 hose adaptors, etc. 

• Contact your Clarke dealer for further information. The use of parts 

other than genuine Clarke replacement parts may result in possible 
safety hazards or decreased pump performance and will invalidate 
your warranty.

Summary of Contents for 7230330

















Reviews: