Clarke 7120310 Operation & Maintenance Instructions Manual Download Page 10

10

Parts & Service: 020 8988 7400 / E-mail: [email protected] or [email protected]

MAINTENANCE

Inspect the pump/hoses regularly to ensure that debris is not blocking the 
passage of water. If you suspect the pump is blocked by silt, leaf debris etc, 
disconnect it from the power supply, disconnect the discharge hose and 
back-flush to clear any blockage using a hosepipe.

Always keep the pump in a clean condition and check regularly for damage 
to the power cable etc.

All electrical connections should be inspected regularly for signs of corrosion 
and cleaned where necessary. It is advisable to apply a film of silicon grease 
on the terminals for added protection.

AFTER USE

After use, and if the pump will not be used over the winter period or if there is 
danger of freezing, always drain the pump body.

If the pump has been used with contaminated or salty water it should be 
thoroughly flushed with clean water following use, both inside and out. It 
should then be drained and covered over if not already sheltered from the 
weather.

If the pump is seized following a period of inactivity it may be possible to free it 
off. Ensure the power supply is turned off before by inserting a screwdriver into 
either the infeed or discharge port and dislodging a jammed impeller. If this is 
not successful it may be necessary to remove the relevant mounting bolts to 
separate the pump body and clean away any incrustation.

Re-prime the pump when returning to service.

In the event that overhaul of the pump or motor is necessary, contact your 
Clarke service department.

ENVIRONMENTAL RECYCLING POLICY

Through purchase of this product, the customer is taking on the 
obligation to deal with the WEEE in accordance with the WEEE 
regulations in relation to the treatment, recycling & recovery and 
environmentally sound disposal of the WEEE.

In effect, this means that this product must not be disposed of with general 
household waste. It must be disposed of according to the laws governing 
Waste Electrical and Electronic Equipment (WEEE) at a recognised disposal 
facility.

Summary of Contents for 7120310

















Reviews: