background image

2

Parts & Service: 020 8988 7400 / E-mail: [email protected] or [email protected]

INTRODUCTION

Thank you for purchasing this CLARKE buffer/polisher.

Before attempting to use this product, please read this manual thoroughly and 
follow the instructions carefully. In doing so you will ensure the safety of yourself 
and that of others around you, and you can look forward to your purchase 
giving you long and satisfactory service.

SPECIFICATIONS

GUARANTEE

This product is guaranteed against faulty manufacture for a period of 12 
months from the date of purchase. Please keep your receipt which will be 
required as proof of purchase.

This guarantee is invalid if the product is found to have been abused or 
tampered with in any way, or not used for the purpose for which it was 
intended. Faulty goods should be returned to their place of purchase, no 
product can be returned to us without prior permission. This guarantee does 
not effect your statutory rights.

ENVIRONMENTAL PROTECTION

Through purchase of this product, the customer is taking on the 
obligation to deal with the WEEE in accordance with the WEEE 
regulations in relation to the treatment, recycling & recovery and 
environmentally sound disposal of the WEEE.

In effect, this means that this product must not be disposed of with general 
household waste but according to the laws governing Waste Electrical and 
Electronic Equipment (WEEE) at a recognised disposal facility.

CBB200

Motor Power

370W

Fuse Rating

5 Amp

Rated Voltage / Frequency

230V / 50Hz

Shaft Diameter

16 mm

No Load Speed

2850 rpm

Wheel Diameter

200 mm

Dimensions

195 x 460 x 235 mm

Weight

9.95 kg

Summary of Contents for 6500490













Reviews: