manualshive.com logo in svg

Clarke 6479600, Operation & Maintenance Instructions Manual

Share
Download
Clarke 6479600 Operation & Maintenance Instructions Manual Download Page 13

13

Parts & Service: 020 8988 7400 / E-mail: [email protected] or [email protected]

MAINTENANCE AND SERVICING

1. After use, remove the drill bit and tap the side of the chuck to remove any 

dust or chippings etc.

2. Keep the handle clean and free from oil and grease.

3. Worn or damaged parts must be replaced by qualified personnel.

4. Clean the tool regularly, use a soft brush and or soft cleaning cloth. DO 

NOT use any chemicals or harsh abrasives to clean the tool.

5. At the end of work, to prevent dust deposits you should use compressed air 

(max.3 bar) to clean out the ventilation holes.

GEARBOX GREASE

Check gearbox occasionally and top up if necessary with a good quality high 
melting point grease. 

1. Remove the 4 hex bolts from the 

grease cover.

2. Remove the cover.

3. Apply sufficient grease to cover 

all visible moving parts.

•  DO NOT overfill the gearbox.

4. Replace the cover and hex bolts 

before using the drill again.

Summary of Contents for 6479600





















Reviews:

No comments

Brands by name

Popular brands

Load more brands