Clarke 6462199 Operation & Maintenance Instructions Manual Download Page 10 | Manualshive

Page: 10 / 16

background image

10

Parts & Service: 020 8988 7400 / E-mail: [email protected] or [email protected]

OPERATION

1. Hold the tool tightly and move the

On/Off switch forward.

• The multi tool will operate

continuously.

2. Slowly apply the tool to the work

piece.

• Apply light pressure as you

move it across the work.

3. Move the switch to the rear to stop the multi tool.

WARNING: MAKE SURE THAT THE POSITION USED DOES NOT CAUSE
FATIGUE WHICH CAN CAUSE LOSS OF CONTROL.

«
...
8
9
10
11
12
...
»

Summary of Contents for 6462199

















Reviews:

No comments

Related manuals for 6462199

Brand: Rapid Pages: 6

Brand: OK-WINDER Pages: 2

Brand: CAME Pages: 2

Brand: Neilsen Pages: 10

Brand: VADANIA Pages: 5

Brand: Park Tool Pages: 2

Brand: Westfalia Pages: 46

Brand: Cornwell Tools Pages: 4

Brand: TE Connectivity Pages: 5

Brand: KS Tools Pages: 4

Brand: Ober Pages: 32

Brand: Performance Tool Pages: 4

Brand: Complete Pages: 5

Brand: Macnaught Pages: 12

Brand: Far Tools Pages: 23

Brand: BGS technic Pages: 8

Brand: Campbell Hausfeld Pages: 4

Brand: Campbell Hausfeld Pages: 24

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands