Clarke 6240015 Operating & Maintenance Instructions Download Page 9

9

Parts & Service: 020 8988 7400 / E-mail: [email protected] or [email protected]

OPERATION

Always carry out the following preliminary checks before connecting the 
jump-start to the car battery:

• Make sure that the vehicle ignition and ALL ancillary equipment - 

lighting, radio etc, is switched off.

• Make sure that the vehicle battery is rated at 12V and is not 

damaged in any way.

• Make sure that the battery terminals are clean and the clamps are 

firm and secure.

• Remove any vehicle battery filler plugs and check the electrolyte 

level. If necessary, top up with distilled water.

• Make sure that the area is well ventilated.

• Take great care not to touch the red positive (+) clamp against the 

black negative (-) clamp.

1. Make sure that the ON/OFF switch is in the OFF position. 

2. Connect the red positive (+) clamp to the positive (+) battery terminal first. 

Take care the clamp does not contact any moving parts or fuel lines.

3. Connect the black negative (-) clamp to the negative (-) battery terminal 

or to a suitable earthing point on the vehicle chassis ensuring the 
connections are firm and secure.

4. Switch the Jump-start, then the vehicle ignition ‘ON’ and leave in this 

condition 

FOR APPROX TWO MINUTES.

 (This will provide the vehicle battery 

with a short ‘boost’ charge to allow for easier starting).

5. Switch the ignition to ‘start’, for NO MORE than 10 seconds.

• If the engine does not start within this time, SWITCH OFF the ignition 

and wait for at least 4 minutes before trying again to prevent 
damage to the jumpstarter due to overheating before trying again. 
After this cooling off period, it is safe to resume trying to start the 
vehicle.

6. Once the vehicle has started, turn the jump-start ON/OFF switch OFF.

7. Once the engine is running, disconnect the earthed clamp FIRST i.e. that 

connected to the chassis or Negative terminal etc, and return it to its 

WARNING: FAILURE TO FOLLOW THE INSTRUCTIONS BELOW AND THE 
SAFETY INSTRUCTIONS ON PAGES 3/4, MAY RESULT IN PERSONAL INJURY, 
DAMAGE TO THE VEHICLE, OR THE POSSIBILITY OF AN EXPLOSION

Summary of Contents for 6240015

















Reviews: