manualshive.com logo in svg

Clarke 6240015, Operating & Maintenance Instructions, Page: 11 / 16

Share
Download
Clarke 6240015 Operating & Maintenance Instructions Download Page 11

11

Parts & Service: 020 8988 7400 / E-mail: [email protected] or [email protected]

USING THE COMPRESSOR

 

(MODEL 1100C ONLY)

For inflating tyres, attach the air hose to the tyre by pushing the connector 
down firmly on the tyre adapter and locking in place by turning the connector 
locking lever through 90 degrees.

Switch on the compressor. The gauge will indicate the air pressure in the tyre.

Pull out the hose and use one of the 
adaptors to connect to the 
accessory being inflated.

• Three adapters are provided 

which allow the compressor to 
be used for inflating air beds, 
footballs etc.

Select the appropriate adapter and 
push the threaded end firmly into the 
air hose connector, locking it in place 
by turning the connector locking lever through 90 degrees.

Turn on the compressor using the switch and note the pressure displayed on 
the gauge. Switch off when the item is fully inflated. Do not exceed the duty 
cycle stated in the specification.

WARNING: DO NOT RUN THE COMPRESSOR FOR MORE THAN 10 MINUTES. 
ALLOW A 10 MINUTE PERIOD TO ELAPSE BEFORE SWITCHING ON AGAIN.

CAUTION: THE AIR PRESSURE GAUGE ON THIS PRODUCT IS FOR 
GUIDANCE ONLY. IT IS IMPORTANT THAT YOU CHECK YOUR TYRE 
PRESSURE WITH A PRESSURE CERTIFIED GAUGE.

Summary of Contents for 6240015

















Reviews:

No comments