background image

3

Parts & Service: 020 8988 7400 / E-mail: [email protected] or [email protected]

 GENERAL SAFETY RULES 

WORK AREA 

1.

Keep the work area clean and well lit

. Cluttered and dark areas invite accidents. 

2.

Do not operate log splitters in explosive atmospheres, such as in the presence of 
flammable liquids, gases or dust.

 Log splitters create sparks which may ignite the 

dust or fumes. 

3.

Keep children and bystanders away while operating the log splitter.

 Distractions can 

cause you to lose control. 

4.

The surface must be perfectly level to prevent the machine from moving during 
operation.

PERSONAL SAFETY 

1.

Stay alert, watch what you are doing and use common sense when operating a log 
splitter. Do not use the log splitter while you are tired or under the influence of drugs, 
alcohol or medication. 

A moment of inattention while operating log splitters may 

result in serious personal injury. 

2.

Use safety equipment. Always wear eye protection.

 Safety equipment such as non-

skid safety shoes, close fitting clothing and suitable work gloves eye and ear 
protection should always be used.

3.

Do not overreach. Keep proper footing and balance at all times. 

This enables better 

control of the log splitter in unexpected situations. 

4.

Dress properly. Do not wear loose clothing or jewellery. Keep your hair, clothing and 
gloves away from moving parts. 

Loose clothes, jewellery or long hair can be caught 

in moving parts. 

USAGE AND CARE 

1.

Do not force the log splitter.

 It will do the job better and safer at the rate for which it 

was designed.

2.

Shut off the engine before making any adjustments, changing accessories, or storing 
the log splitter. 

3.

Store the log splitter out of the reach of children and do not allow persons unfamiliar 
with log splitters or these instructions to operate the log splitter.

 Log splitters are 

dangerous in the hands of untrained users.

4.

Maintain the log splitter. Check for misalignment or binding of moving parts, 
breakage of parts and any other condition that may affect the log splitters 
operation. If damaged, have the log splitter repaired before use. 

Many accidents 

are caused by poorly maintained equipment.

WARNING: READ ALL INSTRUCTIONS. FAILURE TO FOLLOW ALL 
INSTRUCTIONS LISTED BELOW MAY RESULT IN SERIOUS INJURY. SAVE THESE 
INSTRUCTIONS. 

Summary of Contents for 3402042

























Reviews: