background image

2

Parts & Service: 020 8988 7400 / E-mail: [email protected] or [email protected]

INTRODUCTION

Thank you for purchasing this CLARKE Needle Scaler.

Please read all of the safety and operating instructions carefully before using 
this product. In doing so you will ensure the safety of yourself and that of others 
around you, and you can look forward to your purchase giving you long and 
satisfactory service.

GUARANTEE

This product is guaranteed against faulty manufacture for a period of 12 
months from the date of purchase. Please keep your receipt which will be 
required as proof of purchase. 

This guarantee is invalid if the product is found to have been abused or 
tampered with in any way, or not used for the purpose for which it was 
intended. Faulty goods should be returned to their place of purchase, no 
product can be returned to us without prior permission. 

This guarantee does not effect your statutory rights.

SPECIFICATION

Model Number

CAT51

Min. Hose Size (ID)

8mm (5/16” BSP

Max Operating Pressure

90 psi (6.2 bar)

Max Air Consumption

5 cfm (average)

Blows per minute

4500 (@ 6.2 bar)

Piston Stroke

27 mm

Air Inlet Size

1/4“BSP Female

Sound Pressure Level (LpA dB)

95.1 dB(A)

Sound Power Level (LwA dB)

106.1 dB(A)

Vibration Levels

18.2 m/s

Weight

2.8 kg

Summary of Contents for 3110565













Reviews: