background image

6

Parts & Service: 020 8988 7400 / E-mail: Parts@clarkeinternational.com or Service@clarkeinternational.com

OPERATION

After mixing and thinning the paint, fill the paint jar no more than about 2/3 
full. Attach the jar to the airbrush, turn the compressed air on, and depress the 
trigger. Test on an old newspaper or similar and make any necessary spray 
adjustments before spraying the workpiece.

ADJUSTING THE PAINT FLOW

Paint flow and spray pattern are adjusted by turning the air cap at the tip of 
the airbrush. Paint flow is also affected by the amount the trigger is pulled 
back.

The air cap is fully closed when it has been turned fully clockwise. Using the 

thumb and forefinger, turn the air cap anti-clockwise to obtain various 
degrees of paint flow.

Also check the adjustment of the needle sleeve which can also effect paint 
flow when screwed in and out. Maximum flow will be attained by turning the 
needle sleeve assembly approximately two full turns anti-clockwise.

Pull back on the trigger to obtain more paint and a wider coverage.

PAINTING PROCEDURES

1. Prepare the workpiece, masking off any areas not to be painted, (ensuring 

the workpiece is clean and free of dust, grease etc).

2. Hold the nozzle of the airbrush about 6” from the surface being sprayed. 

Use short strokes, moving steadily and parallel to the surface.

3. Spray several light coats, allowing each coat to dry before adding the next 

until the desired coverage is achieved.

Summary of Contents for 3110320

















Reviews: