VRX935VD
23
English
Owner’
s manual
Basic Operations
Turning the liquid crystal panel
horizontal (Air conditioner
operation mode)
When the way the liquid crystal panel is
mounted hinders the operation of the air condi-
tioner, the position of the panel can be turned
horizontal temporarily.
1. Press and hold the [OPEN] button when the
liquid crystal panel is upright, and release
the button when a beep is heard.
2. The liquid crystal panel turns horizontal.
∗
Press the [OPEN] button again when the liquid
crystal panel is in the horizontal position, and
the panel returns to the original position.
∗
Even if the button is not operated for about 10
seconds, the panel returns to the original posi-
tion with a warning sound.
Turning on and off the monitor
1. Pressing and holding the [M.L] button for 1
second or longer turns the monitor off. To re-
turn to the monitor on, press the [M.L] button
once again.
∗
When a button is pressed or during security
monitoring, the monitor-off mode is canceled.
Mute
1. Each time you press the [MUTE] button,
mute is turned on and off. “MUTE” appears
when mute is turned on.
Setting the Beat EQ
• This function is enabled only when the panel is
open.
This unit comes with 3 types of sound tone ef-
fect stored in memory. Select the one you prefer.
∗
The factory default setting is “USER CUSTOM”.
1. Press the [A-M] button to change into the
AUDIO MODE menu.
2. When the AUDIO MODE menu is displayed,
touch the key for the desirable type to select it.
• BASS BOOST
: bass emphasized
• IMPACT
: bass and treble empha-
sized
• EXCITE
: bass and treble empha-
sized mid de-emphasized
• USER CUSTOM : user custom
• TONE BYPASS : no sound effect (Beat EQ
off)
3. When the setting is finished, touch the [RTN]
key or press the [A-M] button to return to the
previous mode.
When the Beat EQ (BASS BOOST, IMPACT,
EXCITE, USER CUSTOM) is set, “B.EQ” ap-
pears in the display.
Note:
• When the separately-sold Multiple Channel Pro-
cessor (DVH920) is used, the bass and treble
tone adjustments cannot be made. To adjust the
tone, refer to the section “Multiple Channel Pro-
cessor Operations”.
Adjusting the non fader output
volume
You can adjust the volume output from the unit’s
non fader output terminal.
1. Press the [A-M] button, then touch the
[DETAIL] key.
2. Touch the [NON-FAD VOL] key.
3. Touch the [
w
] or [
z
] key to adjust to desir-
able level.
∗
The factory default setting is “0”. (Setting
range: –6 to 6)
4. When the adjustment is complete, touch the
[RTN] or press the [A-M] button to return to
the previous mode.
Adjusting the bass
The bass gain, bass frequency (center fre-
quency) and bass Q can be adjusted as follows.
1. Press the [A-M] button, then touch the
[USER CUSTOM] key.
2. Touch the [DETAIL] key, then touch the
[BASS] key.
3. When the bass type selection screen is dis-
played, touch the key for the desirable type
to select it.
4. Touch the [
w
] or [
z
] key to adjust to desir-
able level.
GAIN
: –6 to 8 (The factory default setting
is “0”)
FREQ. : 50Hz/80Hz/120Hz (The factory de-
fault setting is “50”)
Q
: 1/1.25/1.5/2 (The factory default
setting is “1”)
5. When the adjustment is complete, touch the
[RTN] key several times or press the [A-M]
button to return to the previous mode.
