background image

9

Specifications

OWNER’S MANUAL

S

PECIFICATIONS

:

Power Requirement:

DC Application:  +12 volts dc (9-16 volts dc)
AC Application:  90-264 V, 50-60 Hz., 1.1-0.6 A

Power Consumption:

60 watts, Power On (8-12 W Standby)
5 amps (5000 mA)

Weight:

5.4 lb (12 kg)

Dimensions: Panel Only: 17-11/16 x 15-3/16 x 3-5/16 in. (449 x 385 x 84 mm)

With Stand 17-11/16 x 18-9/16 x 8-7/8 in. (449 x 470 x 225 mm)

View Angle:

Hor. +70°/-70° Ver. +70°/-40°

Tilt Angle of Hinge

10° Forward   40° Backwards

Audio Output

3W x 2 Max.

Display Type:

Color TFT Active Matrix LCD

Screen Size:

18.1" (Panel Dimensions 359.0 x 287.2 mm)

Pixel Pitch

0.2805 x 0.2805 mm

Pixels:

1280 x 1024

Screen Resolution:

1,310,720 Dots

Video Input Level (RCA): 1.0 volts peak to peak, NTSC
RGB Input Level:

0.75 volts peak to peak, TTL

No picture on moni-
tor.

Set the TV Tuner function to “TV” mode.

The screen will be blank if no picture
(signal) is inputted.  Choose the proper
input source selection.

The TV tuner is not
set to TV mode 

The Monitor is set to
the wrong signal
input mode.

The LED turns
orange when connect-
ed to the TTX001 or
a home VCR.

This may due to signals reflected off
buildings, mountains, etc.  Check again in
a different place and direction or tune to a
strong TV station.

The signal condition
is poor. The monitor
enters Sleep Mode.

The screen displays
an error message then
the LED turns orange
after 10 seconds.

Switch to another signal input. Check
connections and signal output from your
input source 

No signal or low
signal on the cho-
sen input.

System does not
work.

Replace external fuse with the same
value.  Check the wire connections and
connect it properly.

+12Vdc Fuse blown
or AC Power wires
are not connected.

The screen is dark.
The LED is orange,
not green

Press the power button on the front of the
monitor.  This will wake up the monitor.
This may happen if the temperature in the
vehicle is below 30°F or above 113°F.
Check again when the temperature is
between 30 and 113°F.

The monitor is in the
Sleep Mode.
Usage conditions are
poor.

T

ROUBLESHOOTING

:

Symptom

Cause

Solution

Summary of Contents for VMA1891













Reviews: