Clarion QX-3870N-A Service Manual Download Page 1

QX-3870N-A

- 1 -

NISSAN Motor Genuine
2DIN HDD Navigation
BOSE Specifi cations
for CANADA

NAU-3225KCA-C

Model 

QX-3870N-A

 (Genuine Parts Number 25915 ZZ60D)

Service Manual

This product is a lead free model.

Lead free solder is used in PWB stamped LF mark. 

Please keep the following conditions when you repair.

 1.  Use lead free solder. 

 

* Koki's lead free solder S3X-55M 0.6mm

       (CLARION Parts No.642-0231-01)

 

* Koki's lead free solder S3X-55M 1.0mm

       (CLARION Parts No.642-0231-02)

 2.  Use a nitrogen solder system.

 3.  Do not use "General solder" and "Lead free solder"

 together.

1. NOTES

*  iPod is a trademark of Apple Inc., registered in the U.S. and 

other countries.

Bluetooth  is a trademark owned by Bluetooth SIG, Inc., U.S.A. 

and licensed to Clarion.

We cannot supply the parts not listed in this manual.

* Specifi cation and design are subject to change without notice 

for further improvement.

© Copyright 2012 Clarion Company,Ltd. All rights reserved. 

No portion of this manual can be reproduced in any way, elec-

tronically or otherwise, without the express prior permission of 

the copyright owner.

PDF MANUAL

Clarion Co., Ltd.

7-2,Shintoshin,Chuo-ku,Saitama-shi  330-0081 Japan
After Service Department: Phone +81-48-601-3792 / Fax +81-48-601-3804

Published by After Service Dept.
Printed in Japan
2012/06

No.E7297-00

Summary of Contents for QX-3870N-A























Reviews: