PS-3025K-A,B
- 4 -
pin 48: EEP DO
: O : Serial data output to EEP-ROM.
pin 49: EEP DI
: IN : Serial data input from EEP-ROM.
pin 50: GIX SYS ACC
: O : 6CD-mechanism system ACC control.
pin 51: GIX RESET
: O : Reset pulse output to 6CD-mechanism.
pin 52: NU
: O : Not in use.
pin 53: NU
: O : Not in use.
pin 54: NU
: O : Not in use.
pin 55: NU
: O : Not in use.
pin 56: NU
: O : Not in use.
pin 57: NU
: IN : Not in use.
pin 58: NU
: O : Not in use.
pin 59: NU
: IN : Not in use.
pin 60: VDD
: - : Positive voltage supply.
pin 61: NU
: O : Not in use.
pin 62: GND
: - : Ground.
pin 63: NU
: O : Not in use.
pin 64: NU
: O : Not in use.
pin 65: LCD RESET
: O : Reset pulse output to the LCD.
pin 66: LCD CS
: O : Chip select signal output to the LCD driv-
er.
pin 67: LCD CK
: O : Clock pulse output to the LCD driver.
pin 68: LCD DATA
:I/O: Serial data input/output for the LCD driv-
er.
pin 69: LCD REQ
: IN : The key interrupt request signal input from
the LCD driver.
pin 70: VOL 1 L
: IN : Volume control pulse input from the rota-
ry encoder.
pin 71: VOL 2 L
: IN : Volume control pulse input from the rota-
ry encoder.
pin 72: GIX REQ
: IN : Request signal input from 6CD-mecha-
nism.
pin 73: RDS CK
: IN : RDS clock pulse input.
pin 74: VOL 1 R
: IN : Volume control pulse input from the rota-
ry encoder.
pin 75: VOL 2 R
: IN : Volume control pulse input from the rota-
ry encoder.
pin 76: NU
: O : Not in use.
pin 77: NU
: O : Not in use.
pin 78: NU
: O : Not in use.
pin 79: NU
: O : Not in use.
pin 80: NU
: O : Not in use.
pin 81: NU
: O : Not in use.
pin 82: NU
: O : Not in use.
pin 83: SEL 1
: IN : L = 1CD, H = 6CD.
pin 84: SEL 2
: IN : Refer Table 1.
pin 85: SEL 3
: IN : Refer Table 1.
pin 86: SEL 4
: IN : L = Without EQ.
pin 87: POWER SW
: IN : Power switch ON signal input.
pin 88: CD LOAD
: IN : CD load switch signal input.
pin 89: CD EJECT
: IN : CD eject switch signal input.
pin 90: NU
: O : Not in use.
pin 91: NOISE
: IN : The noise level for RDS.
pin 92: S METER
: IN : The input terminal of the internal A/D con-
verter to monitor the radio field strength.
pin 93: S REMOCON
: IN : Steering wheel remote controller input.
pin 94: A VSS
: - : Analog ground.
pin 95: AUX/TEL ON
: IN : AUX/TEL ON signal input.
pin 96: Vref
: - : Reference voltage.
pin 97: A VCC
: - : Positive voltage supply for the internal
analog section.
pin 98: SD/ST
: IN : At receiving the FM station, this port de-
tects the stereo signal. At seeking or
scanning, this port detects the station de-
tection signal.
pin 99: SD CONT
: O : SD control signal output.
pin100: PLL DI
: IN : PLL serial data input.
Table 1
SX4
SEL 2 ( pin 84 )
L
SEL 3 ( pin 84 )
H