PS-3025K-A,B
- 3 -
MODE L NO.
PART No .
PS-3025K
286-6186-
Cla r io n Co . , L t d
1 2 V ( - ) GROUND
S E RI A L NO.
FREQUENCY RANGE
LW : 153k Hz- 279k Hz
MW ; 531k Hz- 1602k Hz
FM ; 87. 5MHz- 108MHz
39101-80J
S u z u k i
p a r t
No .
39101-80JA
I D:
033942
PS2809
CAUTIONS
This appliance contains a laser system and is classified as
a "CLASS 1 LASER PRODUCT". To use this model prop-
erly, read this Owner's Manual carefully and keep this manual
for your future reference. In case of any trouble with this
player, please contact your nearest"AUTHORIZED service
station". To prevent direct exposure to the laser beam, do
not try to open the enclosure.
Use of controls,adjustment,or performance of procedures
other than those specified herein,may result in hazardous
radiation exposure.
EXPLANATION OF IC
051-5046-90
CL7639V20
Electronic volume with Speed
detector and Acoustic compensator
052-3211-01
M30624MGP-D92GP
System Controller
Terminal Description
pin
1: PLL CK
: O : PLL clock pulse output.
pin
2: PLL DO
: O : PLL serial data output.
pin
3: PLL CE
: O : PLL chip enable signal output.
pin
4: NU
: O : Not in use.
pin
5: NU
: O : Not in use.
pin
6: BYTE
: IN : Data length selection(8bit/16bit).
pin
7: CN VSS
: IN : Connect to GND via a resistor.
pin
8: ANT-ON / TP
: O : Antenna-ON signal output, and the test
signal output.
pin
9: BL CONT
: O : Back light control signal output.
pin 10: RESET
: IN : Reset signal input.
pin 11: X out
: O : Crystal connection.
pin 12: GND
: - : Ground.
pin 13: X in
: IN : Crystal connection.
pin 14: VDD
: - : Positive voltage supply.
pin 15: NMI
: IN : Nonmaskable interrupt. Connect to VDD
via a resistor.
pin 16: ACC DET
: IN : ACC detection signal input.
pin 17: BU DET
: IN : Backup detection signal input.
pin 18: Speed Pulse
: IN : Speed pulse input.
pin 19: BL ON
: O : Back light ON command output.
pin 20: NU
: O : Not in use.
pin 21: NU
: O : Not in use.
pin 22: VOL EQ CK
: O : Clock pulse output to the volume IC or the
equalizer IC.
pin 23: VOL DATA
: O : Serial data output to the volume IC.
pin 24: BEEP
: O : Beep out.
pin 25: 27pin connect
: IN : Connect to 27pin.
pin 26: VLCD ON
: O : LCD-bias-voltage ON-signal output.
pin 27: Ce-NET RX
: IN : Serial data input from the Ce-NET.
pin 28: Ce-NET TX
: O : Serial data output to the Ce-NET.
pin 29: FLASH TX
: O : Flash memory Serial data output.
pin 30: FLASH RX
: IN : Flash memory Serial data input.
pin 31: FLASH CK
: IN : Flash memory Clock.
pin 32: ILL ON
: IN : Illumination ON signal input.
pin 33: GIX SDA
: O : Serial data output to 6CD-mechanism.
pin 34: GIX CK
: O : Serial clock output to 6CD-mechanism.
pin 35: SYS ON
: O : System ON signal output.
pin 36: AMP ON
: O : Audio power amplifier ON signal output.
pin 37: AMP MUTE
: O : Muting signal output to the Audio power
amplifier.
pin 38: NU
: O : Not in use.
pin 39: SYS ACC
: O : ACC detect signal output.
pin 40: CATS TP OUT : O : For CATS test.
pin 41: CD ON
: O : CD ON signal output.
pin 42: RDS DI
: IN : RDS data input.
pin 43: RDS DIS CHG : O : RDS dis-charge signal output.
pin 44: SPDUP/FLS CE : O : Station detection speed control / Flash
memory Chip enable.
pin 45: RDS MUTE
: O : RDS mute signal output.
pin 46: EEP CK
: O : EEP-ROM clock pulse out.
pin 47: EEP CS
: O : EEP-ROM chip select signal out.
DEF P L
DEF N L
DEF P R
DEF N R
AUX L
AUX R
NC
NC
CD L
CD R
NC
NC
FM L
FM R
43
44
45
46
47
48
49
50
51
52
53
54
55
56
42
GV L
V
olume(Loud) T
one
1
GV R
Input select. Gain adj.
41
VOL
IN L
LOUD L
T
ONE L
F
AD IN L
40
39
38
3
4
5
2
Front
Left
Front
Right
Rear
Left
RL OUT
RL Low Filter
RL High Filter
24
23
22
NC
FL OUT
FL Low Filter
FL High Filter
28
27
26
25
NC
FR OUT
FR Low Filter
FR High Filter
21
20
19
18
Rear
Right
RR OUT
RR Low Filter
RR High Filter
17
16
15
14 NC
C
SW
NC
NC
NC
13
12
11
10
D GND
9
CLOCK
8
DA
T
A
7
D VDD
LOGIC
36
V
ref IN
35
A G
N
D
34
A V
C
C
VOL
IN R
LOUD R
T
ONE R
F
AD IN R
37
NC
NC
NC
NC
NC
NC
NC
NC
6
29
30
31
32
33
37
