Clarion ProSecurity SR9000 Installation Manual Download Page 53

Page: 53 / 60

table of zones

When using the Diagnostic functions, use the Table of Zones to see which input has triggered the system. It is

also helpful in deciding which input to use when connecting optional sensors and switches.

NOTE

: The Warn Away® response does not report on the LED.

shutdown diagnostics

1. With the ignition OFF, press and

HOLD

the Valet/Program switch.

2. Turn the ignition ON and then back OFF while

HOLDING

the Valet/Program switch.

3. Release the Valet/Program switch.

4. Press and release the Valet/Program switch. The LED will report the last shutdown for one minute or until

the ignition is turned on.

LED FLASHES

SHUTDOWN MODE

One

Timed out

Two

Over-rev shutdown

Three

Low or no RPM

Four

Transmitter shutdown (or optional push-button)

Six

(-) Shutdown (H3/4 GRAY) or (+) Shutdown (H3/3 BROWN)

Seven

(-) Neutral safety shutdown (H3/1 BLACK/WHITE)

Eight

Wait-to-start timed out

to perform shutdown diagnostics

ZONE NO.

TRIGGER TYPE

INPUT DESCRIPTION

Trunk Input

BLUE (H1/7)

Multiplexed Shock Sensor Input Mux BLUE wire.

Door Trigger

GREEN (H1/8) and VIOLET (H1/6).

Multiplexed Shock Sensor Input Mux GREEN wire

Ignition

Yellow ribbon harness wire

Hood Brake Trigger

GRAY on the 6-pin shutdown harness.

Summary of Contents for ProSecurity SR9000

























































Search results

Summary of Contents for ProSecurity SR9000

Reviews:

Related manuals for ProSecurity SR9000

Brands by name

Popular brands

Clarion ProSecurity SR9000, Installation Manual

Search results

Summary of Contents for ProSecurity SR9000

Reviews:

Related manuals for ProSecurity SR9000

Brands by name

Popular brands