HOW TO INSTALL
Installation Precautions
Be sure to read the Safety Precautions prior to installation and follow them throughout.
Installation Precautions
1
Camera ECU box
2-
2
Mounting brackets
4-
3
M5 × 12 mm hex bolts with washers
■
Precautions for Installing Mounting Brackets
2
Mounting bracket
3
M5 × 12 mm hex bolts with washers
Recommended torque : 0.6 N·m to 1.2 N·m
1
Camera ECU box
6 mm to 8 mm (Length protruding inside)
CAUTION
· If you should lose screws that come with the device, use either M5 × 12 mm hex bolts with washers or
screws of a length that protrude inside the ECU box to a depth of 6 mm to 8 mm.
Be sure to follow this precaution as using longer bolts may result in damage to the threads, prevent the
mounting bracket from getting tight enough and/or cause the screws to come out during operation of
the vehicle.
· The recommended torque for
3
M5 × 12 mm hex bolts with washers is 0.6 N·m to 1.2 N·m.
Be careful not to damage the threads by over-tightening the bolts.
WIRING AND CONNECTIONS
Wiring Precautions
Be sure to read the Safety Precautions prior to wiring and follow
them throughout.
Wiring Precautions
WARNING
Failure to do so may result in shock and/or
injury due to a short circuit.
It may also lead to damage to the system
components due to a short circuit.
• Disconnect the negative terminal of the battery before connecting the
cables.
Main
power supply
GND
Accesorry
power supply
CAM 1
カメラ
1
CAM-2
カメラ
-2
CAM-3
カメラ
-3
CAM-4
カメラ
-4
40P connector
Electrical system
connector (12P connector)
16P connector
32P connector
Black
Black
Black
Black
Yellow
Yellow
Yellow
Black
Red
White
Black
White
Blue/White
Green/White
Purple/White
Brown/Red
Camera input terminal.
Connect if using CAM 1 /
カメラ
1.
Camera input terminal.
Connect if using CAM-2 /
カメラ
-2.
Camera input terminal.
Connect if using CAM-3 /
カメラ
-3.
Camera input terminal.
Connect if using CAM-4 /
カメラ
-4.
Image OUT terminal (RCA connector).
Connect to monitor.
There are 2 identical connectors, and either can be used.
Backup power (DC +12V/24V)
Connect to the
⊕
power source that normal supplies power.
Ground (GND)
Connect to a metal part of the vehicle.
ACC power (DC +12V/24V)
Connect to
⊕
power supply that turnsON/OFF with the ignition key.
Spare signal
For use in situations like the door signal for a bus.
Connect to the
⊕
power supply that is supplied when the door is open.
Connect to the interface box (sold separately) used during calibration and setup.
Fuse 5A
Fuse 5A
Included:
5
32P connection cable
Included:
4
12P electrical system cable
Included:
6
40P connection cable
1
Camera ECU box
connector panel
L directional indicator signal
Connect to the
⊕
power supply that is supplied when the left directional indicator is
blinking.
R directional indicator signal
Connect to the
⊕
power supply that is supplied when the right directional indicator is
blinking.
Reverse signal (DC 10.8V to 28V)
Connect to the
⊕
power supply that is supplied when the gear shift is in the reverse
position.
Connect to the 16P connector of the
Camera ECU box.
Connect to a screen toggling switch
(RCB-210), which is sold separately.
CAUTION
CAUTION
Fuse
Fuse case
Terminal
on vehicle side
· When replacing a fuse, be sure to use one of the same
capacity.
· Putting in the wrong fuse may cause a fault, so check
the amperage of the fuses before replacing them.
When a fuse blows, follow the procedures below for preventing a short circuit and
replace the blown fuse with one of the same capacity.
Take care that the terminal on the vehicle side
does not touch any other metal part.
1. Disconnect the 12P electrical system cable.
2. Make sure all the wires are connected correctly.
3. After making sure everything is correct, replace the blown fuse with one of the
same capacity.
Camera Connections
For an outline of where to make camera connections, see the column for camera connection points for your system.
For details, such as on vehicle type or the cameras to connect for a given system specification, see the PDF manual in the
PC setup application. Please take care as a mistake in the camera connection points will prevent displaying the images cor-
rectly.
Camera Connection
Points by System
Camera System
2 Camera
3 Camera
4 Camera
2+2 Camera
Vehicle example
Truck (Right
steering wheel)
Truck (Left
steering wheel)
Shovel
Bus
Truck (Right
steering wheel)
Truck (Left
steering wheel)
Camera IN
Terminal
Harness Tag
CAM 1
カメラ
1
Not connected
Not connected
Not connected
Front
OP:
Left-rear corner
OP:
Right-rear corner
CAM-2
カメラ
-2
Not connected
Right
Right
Right
OP:
Right-rear corner
Right
CAM-3
カメラ
-3
Left
Not connected
Left
Left
Left
OP:
Left-rear corner
CAM-4
カメラ
-4
Rear
Rear
Rear
Rear
Rear
Rear
OP: Optional
Camera Connections
