Clack Valves WS1.5 Installation & Service Manual Download Page 17

Page: 17 / 52

WS1.5", 2" and 2"QC Drawings and Service Manual

Page 17

Table 3

Troubleshooting Procedures

Problem

Possible Cause

Solution

1. No Display on PC Board

a. No power at electric outlet

a. Repair outlet or use working outlet

b. Control valve Power Adapter not plugged into

outlet or power cord end not connected to PC
board connection

b. Plug Power Adapter into outlet or connect

power cord end to PC Board connection

c. Improper power supply

c. Verify proper voltage is being delivered to

PC Board

d. Defective Power Adapter

d. Replace Power Adapter

e. Defective PC Board

e. Replace PC Board

2. PC Board does not display correct time of day

a. Power Adapter plugged into electric outlet

controlled by light switch

a. Use uninterrupted outlet

b. Tripped breaker switch and/or tripped GFI

b. Reset breaker switch and/ or GFI switch

c. Power outage

c. Reset time of day. If PC Board has battery

back up present the battery may be
depleted. See Front Cover and Drive
Assembly drawing for instructions.

d. Defective PC Board

d. Replace PC Board

3. Display does not indicate that water is

owing.

Refer to user instructions for how the display
indicates water is

owing

a. Bypass valve in bypass position

a. Turn bypass handles to place bypass in

service position

b. Meter is not connected to meter connection on

PC Board

b. Connect meter to three pin connection

labeled METER on PC Board

c. Restricted/ stalled meter turbine

c. Remove meter and check for rotation or

foreign material

d. Meter wire not installed securely into three pin

connector

d. Verify meter cable wires are installed

securely into three pin connector labeled
METER

e. Defective meter

e. Replace meter

f. Defective PC Board

f. Replace PC Board

4. Control valve regenerates at wrong time of day

a. Power outage

a. Reset time of day. If PC Board has battery

back up present the battery may be
depleted. See Front Cover and Drive
Assembly drawing for instructions.

b. Time of day not set correctly

b. Reset to correct time of day

c. Time of regeneration set incorrectly

c. Reset regeneration time

d. Control valve set at ”on 0” (immediate

regeneration)

d. Check programming setting and reset to

NORMAL (for a delayed regen time)

e. Control valve set at ” on 0” (delayed

and/ or immediate)

e. Check programming setting and reset to

NORMAL (for a delayed regen time)

5. Time of day

ashes on and off

a. Power outage

a. Reset time of day. If PC Board has battery

back up present the battery may be
depleted. See Front Cover and Drive
Assembly drawing for instructions.

6. Control valve does not regenerate
automatically when the correct button(s) is
depressed and held. For TC valves the buttons are

▲

▼

. For all other valves the button is REGEN

a. Broken drive gear or drive cap assembly

a. Replace drive gear or drive cap assembly

b. Broken Piston Rod

b. Replace piston rod

c. Defective PC Board

7. Control valve does not regenerate
automatically but

does

when the correct button(s)

is depressed and held. For TC valves the buttons
are

▲

▼

. For all other valves the button is

REGEN

a. Bypass valve in bypass position

a. Turn bypass handles to place bypass in

service position

b. Meter is not connected to meter connection on

PC Board

b. Connect meter to three pin connection

labeled METER on PC Board

c. Restricted/ stalled meter turbine

c. Remove meter and check for rotation or

foreign material

d. Incorrect programming

d. Check for programming error

e. Meter wire not installed securely into three pin

connector

e. Verify meter cable wires are installed

securely into three pin connector labeled
METER

f. Defective meter

f. Replace meter

g. Defective PC Board

g. Replace PC Board

Summary of Contents for WS1.5





















































Search results

Summary of Contents for WS1.5

Reviews:

Clack Valves WS1.5, Installation & Service Manual, Page: 17 / 52

Search results

Summary of Contents for WS1.5

Reviews: