Cisco Versatile Interface Processor (VIP6-80) (VIP6-80) Installation And Configuration Manual Download Page 2 | Manualshive

Page: 2 / 40

background image

2

Versatile Interface Processor (VIP6-80) Installation and Configuration Guide

OL-5078-01

•

Guidelines for Removal and Installation, page 15

•

Removing a VIP6-80, page 18

•

Removing and Installing Port Adapters, page 19

•

Installing a VIP6-80, page 24

•

Performing a Basic Configuration, page 25

•

Checking the VIP6-80 Installation, page 26

•

Maintenance Procedures, page 32

•

Troubleshooting, page 36

•

Obtaining Documentation, page 37

•

Obtaining Technical Assistance, page 38

•

Obtaining Additional Publications and Information, page 39

Related Documentation

Your router and the Cisco IOS software running on it contain extensive features and functionality, which
are documented in the following resources:

•

Cisco IOS software:

For configuration information and support, refer to the modular configuration and modular
command reference publications in the Cisco IOS software configuration documentation set that
corresponds to the software release installed on your Cisco hardware.

Note

You can access Cisco IOS software configuration and hardware installation and maintenance
documentation on the World Wide Web at

http://www.cisco.com

. Translated documentation is

available at the following URL:

http://www.cisco.com/public/countries_languages.shtml

.

•

Cisco microcode:

For information on upgrading microcode in Cisco 7500 series routers, see the Cisco IOS
Configuration Fundamentals Configuration Guides for the mainline software release that you are
running. For information on upgrading software and microcode in Cisco 7000 series routers, refer
to the manual

Upgrading Software and Microcode in Cisco 7000 Series Routers,

available online at

http://www.cisco.com/univercd/cc/td/doc/product/software/ssr921/7k_921cn/54755.htm

.

•

Cisco 7000 series routers:

For hardware installation and maintenance information on the Cisco 7000 series routers, refer to the

Cisco 7000 Hardware Installation and Maintenance

guide available online at

http://www.cisco.com/univercd/cc/td/doc/product/core/cis7000/7000_him/index.htm

.

•

Cisco 7500 series routers:

For hardware installation and maintenance information on the Cisco 7500 series routers, refer to the

Cisco 7500 Installation and Configuration Guide

available online at

http://www.cisco.com/univercd/cc/td/doc/product/core/cis7505/cicg7500/index.htm

.

•

For international agency compliance, safety, and statutory information for WAN interfaces:

–

Site Preparation and Safety Guide

online at

http://www.cisco.com/univercd/cc/td/doc/product/lan/cat4000/hw_doc/safety/index.htm

«
1
2
3
4
...
»

Summary of Contents for Versatile Interface Processor (VIP6-80) (VIP6-80)









































Reviews:

No comments

Related manuals for Versatile Interface Processor (VIP6-80) (VIP6-80)

Brand: D-Link Pages: 29

DGS-3700 Series

Brand: D-Link Pages: 292

Brand: D-Link Pages: 140

DGS-1224T - Web Smart Switch

Brand: D-Link Pages: 61

DI-LB604 - Load Balancing Router

Brand: D-Link Pages: 14

Brand: D-Link Pages: 2

Brand: D-Link Pages: 45

Brand: D-Link Pages: 218

DES-3528 - xStack Switch - Stackable

Brand: D-Link Pages: 322

DIR-130 - Broadband VPN Router

Brand: D-Link Pages: 10

DIR-130 - Broadband VPN Router

Brand: D-Link Pages: 4

DIR-130 - Broadband VPN Router

Brand: D-Link Pages: 13

Brand: D-Link Pages: 13

DI-804HV - Express ENwork Router

Brand: D-Link Pages: 19

Brand: D-Link Pages: 12

Brand: D-Link Pages: 8

Brand: D-Link Pages: 16

Brand: D-Link Pages: 7

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands