Cisco UCS 6454 Installation Manual Download Page 17

Page: 17 / 68

The maximum length of fiber optic runs is limited to 300 meters. This is imposed by our use of
802.3X/802.1Qbb Priority Pauses. SFP-10G-LR is supported between fabric interconnect and FEX, but the
300 m limit still applies.

Note

QSFP Transceivers and Cables

The Cisco 6454 Fabric Interconnect supports Cisco 40GGBASE and 100GBASE Quad Small Form Factor
(QSFP) transceiver modules.

Table 4: Supported QSFP Transceivers and Cables

Description

Model

40 GbE Tranceivers

40GBASE-ER4, 1310 nm, SMF with OTU3 data-rate support

QSFP-40G-ER4

40GBASE-LR4, 1310 nm, SMF with OTU3 data-rate support

QSFP-40G-LR4

40GBASE-LR4-Lite, 1310 nm, SMF

WSP-Q40GLR4L

40GBASE-SR4 QSFP module (multimode fiber [MMF]), 100 meter

QSFP-40G-SR4

40GBASE-SR4 QSFP module (multimode fiber [MMF]), 100 meter

QSFP-40G-SR4-S

Cisco 40GBASE-LR4 QSFP+ transceiver module for SMF, duplex LC
connector

QSFP-40G-LR4

Cisco 40GBASE-LR4 QSFP+ transceiver module for SMF, duplex LC
connector

QSFP-40G-LR4-S

Cisco 40GBASE-SR-BiDi, duplex MMF (LC)

QSFP-40G-SR-BD

100 GbE Tranceivers

100GBASE SR4 QSFP Transceiver, MPO, 100m over OM4 MMF

QSFP-100G-SR4-S

100GBASE LR4 QSFP Transceiver, LC, 10km over SMF

QSFP-100G-LR4-S

100GBASE CWDM4 QSFP Transceiver, 2km over SMF

QSFP-100G-SM-SR

40 GbE QSFP Cables

Cisco 40GBASE-CR4 QSFP direct-attach copper cable, 1-meter, passive

QSFP-H40G-CU1M

Cisco 40GBASE-CR4 QSFP direct-attach copper cable, 3-meter, passive

QSFP-H40G-CU3M

Cisco 40GBASE-CR4 QSFP direct-attach copper cable, 5-meter, passive

QSFP-H40G-CU5M

Cisco 40GBASE-CR4 QSFP direct-attach copper cable, 7-meter, passive

QSFP-H40G-ACU7M

Cisco 40GBASE-CR4 QSFP direct-attach copper cable, 10-meter, passive

QSFP-H40G-ACU10M

Cisco UCS 6454 Fabric Interconnect Hardware Installation Guide

Product Overview

QSFP Transceivers and Cables

Summary of Contents for UCS 6454




































































Search results

Summary of Contents for UCS 6454

Reviews:

Brands by name

Popular brands

Cisco UCS 6454, Installation Manual

Search results

Summary of Contents for UCS 6454

Reviews:

Brands by name

Popular brands