background image

16 1200-Watt AC-Input Power Supply Replacement Instructions

Electric Shock Warning

Timesaver

 The system can identify which type of power supplies are in your chassis: DC-input or

AC-input. As a general precaution, use the show environment all command and note the type of
power supply indicated in each of your chassis (indicated as either “1200W DC” or “1200W AC”).
Record and save this information in a secure place.

This completes the power supply installation. Refer to the Cisco 7513 Hardware Installation and
Maintenance
 publication for installation troubleshooting procedures, and to the Router Products
Command Reference
 publication for descriptions and examples of software features and commands.

Electric Shock Warning

Warning

This unit might have more than one power cord. To reduce the risk of electric shock,

disconnect the two power supply cords before servicing the unit.

Waarschuwing

Dit toestel kan meer dan één netsnoer hebben. Om het risico van een elektrische schok te

verminderen, dient u de stekkers van de twee netsnoeren uit het stopcontact te halen voordat u het toestel een
servicebeurt geeft.

Varoitus

Tässä laitteessa saattaa olla useampi kuin yksi virtajohto. Irrota molemmat virtalähteestä tulevat

johtimet ennen laitteen huoltamista, jotta vältät sähköiskun vaaran.

Attention

Il est possible que cette unité soit munie de plusieurs cordons d'alimentation. Pour éviter les

risques d'électrocution, débrancher les deux cordons d'alimentation avant de réparer l'unité.

Warnung

Diese Einheit hat möglicherweise mehr als ein Netzkabel. Zur Verringerung der

Stromschlaggefahr trennen Sie beide Netzgerätekabel ab, bevor Sie die Einheit warten.

Avvertenza

Questa unità potrebbe essere dotata di più di un cavo di alimentazione. Per ridurre il rischio di

scossa elettrica, scollegare i due cavi di alimentazione prima di procedere alla manutenzione dell’unità.

Advarsel

Denne enheten kan være utstyrt med mer enn én strømledning. Koble fra de to strømledningene

før det utføres reparasjonsarbeid på enheten for å redusere faren for elektriske støt.

Aviso

Esta unidade poderá ter mais do que um cabo de alimentação. Para reduzir o risco de choque eléctrico,

desligue os dois cabos de alimentação antes de efectuar reparações na unidade.

¡Atención!

Puede ser que este equipo posea más de un cable de alimentación.  Para reducir el riesgo de

descarga eléctrica, desenchufar los dos cables antes de proceder al mantenimiento de la unidad.

Varning!

Denna enhet kan vara försedd med mer än en nätsladd. För att minska risken för

elektriska stötar skall båda nätsladdarna dras ur innan du utför underhållsarbete på enheten.

Summary of Contents for PWR-7513-AC



















Reviews: