Cisco ONS 15540 ESPx Hardware Installation Manual Download Page 66 | Manualshive

Page: 66 / 214

background image

Chapter 2 Installing the Cisco ONS 15540 ESPx

Installing the Drawers

2-10

Cisco ONS 15540 ESPx Hardware Installation Guide

78-16436-01

Installing the Drawers

The process for installing the cable storage and cross connect drawers is the same.
The order of placement beneath the chassis is important and should be installed
in the following order from top to bottom:

1.

Cable storage drawer

2.

Cross connect drawer

3.

Cross connect drawer

4.

Cable storage drawer

5.

Cross connect drawer

6.

Cross connect drawer

The first cable storage drawer can be used for direct connections and storage for
connections made using the first and second cross connect drawers. Each cable
storage drawer stores cables for two cross connect drawers.

The cross connect and cable storage drawers ship with the rack mount ears already
installed. To install the cross connect and cable storage drawers into the rack,
follow these steps:

Step 1

Hold the drawer with both hands and position the drawer in the rack beneath the
chassis. (See

.) All drawers following this first one can be stacked

directly underneath each other.

«
...
64
65
66
67
68
...
»

Summary of Contents for ONS 15540 ESPx























































































































































































































Reviews:

No comments

Related manuals for ONS 15540 ESPx

Brand: Hankscraft Runxin Pages: 53

Brand: S-COM Pages: 400

Brand: Daikin Pages: 2

Brand: Daikin Pages: 12

Brand: Daikin Pages: 12

Brand: Daikin Pages: 46

Brand: Daikin Pages: 21

Brand: Daikin Pages: 20

Brand: GCE Pages: 24

Brand: Haldex Pages: 8

Brand: Jäger Pages: 50

Brand: RADEMACHER Pages: 48

Brand: Saftronics Pages: 13

Brand: Absima Pages: 5

Brand: DSEGenset Pages: 74

Brand: ITALFARAD Pages: 32

Brand: Ashly Pages: 1

Brand: OneFex Pages: 24

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands