Cisco NME-16ES-1G - Etherswitch Service Mod 16 Features Manual Download Page 49

Page: 49 / 88

Cisco EtherSwitch Service Modules Feature Guide

How to Configure the Cisco EtherSwitch Service Module

Cisco IOS Release 12.2(25)SEC

Examples

This section provides the following examples:

•

Sample Output for the service-module gigabitethernet shutdown Command, page 49

•

Sample Output for the service-module gigabitethernet reset Command, page 49

•

Sample Output for the service-module gigabitethernet reload Command, page 49

Sample Output for the service-module gigabitethernet shutdown Command

The following example shows what appears when you enter the

service-module gigabitethernet

slot/unit

shutdown

command:

Router#

service-module gigabitethernet1/0 shutdown

Shutdown is used for Online removal of Service Module.

Do you want to proceed with shutdown?[confirm]

Use service-module reset command to recover from shutdown.

Note

At the confirmation prompt, press

Enter

to confirm the action or

to cancel.

Sample Output for the service-module gigabitethernet reset Command

The following example shows what appears when you enter the

service-module gigabitethernet

slot/unit

reset

command:

Router#

service-module gigabitethernet1/0 reset

Use reset only to recover from shutdown or failed state

Do you want to reset?[confirm]

Note

At the confirmation prompt, press

Enter

to confirm the action or

to cancel.

Sample Output for the service-module gigabitethernet reload Command

The following example shows what appears when you enter the

service-module gigabitethernet

slot/unit

reload

command:

Router#

service-module gigabitethernet1/0 reload

Do you want to proceed with reload?[confirm]

Note

At the confirmation prompt, press

Enter

to confirm the action or

to cancel.

Step 2

service-module gigabitethernet

slot

unit

reset

Example:

Router# service-module gigabitethernet1/0 reset

Performs a hardware reset of the Cisco EtherSwitch service
module.

Step 3

service-module gigabitethernet

slot

unit

reload

Example:

Router# service-module gigabitethernet1/0

reload

Performs a graceful halt and reload of the Cisco
EtherSwitch service module operating system.

Command or Action

Purpose

Summary of Contents for NME-16ES-1G - Etherswitch Service Mod 16

























































































Search results

Summary of Contents for NME-16ES-1G - Etherswitch Service Mod 16

Reviews:

Related manuals for NME-16ES-1G - Etherswitch Service Mod 16

Brands by name

Popular brands

Cisco NME-16ES-1G - Etherswitch Service Mod 16, Features Manual

Search results

Summary of Contents for NME-16ES-1G - Etherswitch Service Mod 16

Reviews:

Related manuals for NME-16ES-1G - Etherswitch Service Mod 16

Brands by name

Popular brands